Hitachi CP-X328 user manual Replacing the lamp

Page 27

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2 7 ) and "Regarding the Indicator Lamps" (Vol.2 8 ) for details.)

1

Turn off the projector, and unplug the

power cord. Allow the lamp bulb to cool

 

for at least 45 minutes, and prepare a

 

new lamp (sold separately: DT00511)

 

 

 

 

2

After making sure that the projector has

cooled adequately, slowly flip over the

projector, so that the bottom is facing up

5

Insert the new lamp, and tighten the 1

screw firmly to lock it in place

• Also steadily push the opposite side of the screwed side of the

lamp into the unit.

3 Unscrew the 2 screws, and remove the lamp cover

6

Replace the lamp cover, and tighten

the 2 screws firmly to lock it in

place

4

Unscrew the 1 screw, and slowly pull

out the lamp by the handle

• Be careful not to touch the inside of the lamp case.

7

Slowly turn the projector so that

the top is facing up

 

 

 

 

8

Turn on the projector power, and using

the menu, reset the lamp timer

• To reset the lamp timer, from the OPTION menu, select LAMP TIME.

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

Do not use with lamp cover removed.

Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON.

NOTE The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp.

26

Downloaded from www.Manualslib.com manuals search engine

Image 27
Contents CP-S318W/CP-X328W CP-S318/CP-X328ENGLISHContents Projector Features Power cord Devices you will be using to the projectorPart Names Indicates the correspondingReference Cursor buttons Auto button Blank button Volume button Mute buttonFreeze button Keyboard buttons Position buttonAdjusting the Projectors Elevator Feet Setting UP the ProjectorAdjusting the Screen Size and Projection Distance ScreenTop view Side view Connecting Your Devices Function Projector Port Connection Cables Ports and CablesConnecting to a Computer Connecting Your DevicesConnecting to a VCR Connecting to a DVD PlayerConnecting to a Display Monitor Closecover the battery Using the Remote ControlPutting batteries into the remote control unit Operating the remote controlTurning on the Power Selecting an Input Signal Turning OFF the Power Temporarily Muting the Sound Adjusting the VolumePress the Volume button Press Buttons to adjust VolumeAdjusting the Position Use Buttons to adjust PositionPress the Position button Press the Auto button Using the Automatic Adjustment FeatureAutomatic Adjustment for RGB Input Automatic Adjustment for Video InputOn the screen to aid you in correcting the distortion Correcting Keystone DistortionsPress the Keystone button As illustrated on the right, a dialog will appearFreezing the Screen Using the Magnify FeatureSignal Searching Selecting the Aspect RatioTemporarily Blanking the Screen Press Buttons to adjust the level Using the Menu FunctionsSelect a menu using Buttons Then press Or Enter button Select an item using Buttons, then press Or Enter buttonOperating the PC Screen Available Functions Remote Control OperationHigh Voltage High Temperature High Pressure LampDo not use the projector with the lamp cover removed Replacing the lamp Caring for the air filter AIR FilterReplacing the air filter Caring for the lens Caring for the cabinet and remote control transmitterOther Care Caring for the inside of the projectorFor Technical see the end of this manual Multifunctional Settings Main MenuMain Menu PICTURE2 Menu Picture 1 MenuPicture 2 Menu PICTURE1 MenuVideo Input MenuInput Menu AutoStart UP Screen MenuScreen Menu BlankAuto OFF VolumeOption Menu Option MenuRelated Messages Power Lamp Temp Regarding the Indicator LampsVol.2-6 Phenomena That May Easily Be Mistaken for Machine DefectsVol.2-2 Vol.2-3Unit mm SpecificationsDimension Diagram SpecificationWarranty and AFTER-SERVICE Sub 15-pin Shrink Mini Din 4-pin Signal Connector PIN AssignmentSignal Terminal Specification RGB in 1/2Resolution FH kHz FV Hz Rating Signal mode Display mode Example of Computer SignalInitial SET Signals USB Mouse Connection to the Mouse ControlProtocol Command dataConsist of header 7 bytes + command data 6 bytes RS-232C CommunicationIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset Command日本語 Command data chartBe EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices Hitachi France Hitachi Europe GmbHHitachi Sales Europe GmbH Hitachi Business Systems Nordic

CP-X328 specifications

The Hitachi CP-X328 is a versatile and reliable projector designed to meet the needs of both educational institutions and business environments. Known for its robust performance and user-friendly features, the CP-X328 delivers an exceptional viewing experience, making it a popular choice among users.

One of the standout features of the CP-X328 is its impressive brightness capacity. With a brightness rating of 3,000 ANSI lumens, this projector ensures clear and vivid images even in well-lit rooms. This makes it an ideal choice for classrooms and conference rooms where ambient light can be a challenge. Coupled with a high contrast ratio of 2000:1, the projector allows for rich colors and deeper blacks, enhancing the overall picture quality.

The CP-X328 utilizes 3LCD technology, which is known for its ability to produce bright and true-to-life colors. This technology ensures that images remain consistent and vibrant while minimizing the potential for color distortion or fading over time. Users will appreciate the projector's ability to reproduce detailed graphics and text, making it suitable for both presentations and educational purposes.

In terms of connectivity, the CP-X328 is equipped with a variety of ports to accommodate multiple devices. It includes HDMI, VGA, USB, and RCA inputs, allowing users to connect laptops, cameras, and other multimedia devices effortlessly. This versatility ensures that the projector can be integrated into various setups, whether in a classroom, a meeting room, or for home entertainment.

The projector also features a long lamp life, rated at approximately 5,000 hours in standard mode and up to 6,000 hours in eco mode. This extended lifespan minimizes maintenance costs and downtime, making it a cost-effective choice for long-term users. Additionally, the silent operation of the CP-X328, with a noise level as low as 29 decibels in eco mode, allows for a distraction-free experience during presentations or lectures.

Lastly, the Hitachi CP-X328 is designed with ease of use in mind. With a user-friendly interface, intuitive remote control, and lens shift capabilities, setting up and adjusting the projector is a hassle-free process. Whether you are delivering a presentation or screening a video, the CP-X328 ensures that you can focus on your content rather than on complex technology.

In conclusion, the Hitachi CP-X328 is a reliable projector that combines impressive brightness, advanced 3LCD technology, versatile connectivity options, and user-friendly features, making it an excellent choice for a variety of environments.