Kyocera FS-9130DN, FS-9530DN manual Error Messages, Image adapt

Page 63

 

Troubleshooting

 

 

 

 

Message

Corrective Action

 

 

Warning

Printing job cannot be done in current resolution because there is not enough

image adapt

internal memory. Try adding more memory or changing resolution.

Warning

The printer’s internal memory is running low due to the number of fonts and

low memory

macros downloaded. Print a status page to see how much user memory is left,

 

and try deleting unnecessary fonts and macros.

;:Alarm buzzer sounds when an error occurs. Press [CANCEL] to stop the alarm buzzer.

Error Messages

 

The following table lists error messages that can be dealt with by the user.

 

 

Message

Corrective Action

 

 

e-MPS not stored

The e-MPS job cannot be stored because RAM disk is disabled, RAM disk size is

Press GO

insufficient, hard disk is not installed, or hard disk is full. Press [GO] to print error

;

report.

File not found

VMB: A VMB tray that was specified for output does not contain any jobs, or the

Press GO

VMB tray is not being used. Confirm the VMB tray.

 

If Auto Continue is set to On, printing will be automatically resumed after a preset

;

period of time.

Format error

This message appears when the printer is in the ready state and the memory card

Memory card

is not formatted, and therefore cannot be read or written.

Format error

Initialization (formatting) of the hard disk is required. Initialize the hard disk.

Hard disk

 

Hard disk err ##

Look at the error code given in place of ## and refer to the corresponding

Press GO

description given below.

 

01: Hard disk format error. If this error recurs even if the power has been turned

 

off and then on, reformat the hard disk.

 

02: The disk system is not installed. Recheck the requirements for using the

 

system and the devices.

 

04: There is no available hard disk space. Delete unnecessary files, etc., to free

 

up space.

 

05: The specified file does not exist in the hard disk.

 

06: There is no memory available to the hard disk system. Increase the

 

available memory.

 

10: Formatting is not possible because host data is being spooled on the hard

 

disk.Wait until Ready is displayed, and then format.

 

20: The hard disk was installed in the incorrect slot (OPT). Reinstall the hard

 

disk in a different slot (HDD).

 

85: VMB; Alias error (the alias setting was lost, or the VMB tray corresponding

 

to the alias does not exist). Set the alias again.

 

97: Code job; The number of permanent code jobs reached the limit value, and

 

no more can be saved. Either delete some unnecessary jobs, etc., or

 

increase the limit.

;

99: A print job for the specified ID does not exist in the hard disk.

OPERATION GUIDE

4-11

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Operation Guide Page Contents Operation Guide Regarding Tradenames Legal and Safety InformationUSB License Limited WarrantyLicense Agreements IBM Program License AgreementGeneral Limitation of RemediesMonotype Imaging License Agreement Typeface Trademark AcknowledgementFCC Statement for users in the United States Compliance and ConformityPrecautions for Use Radio Frequency Transmitter Safety InformationLaser Safety Laser NoticeOperation Guide Cdrh Regulations Ozone ConcentrationDeclaration of Conformity for U.S.A CE Marking Directive Canadian Department of Communications Compliance Statement Declaration of Conformity AustraliaDuplex Printing EN ISODisclaimer Energy Saving Control FunctionEnergy Star Energy Star Program Xvii Symbols Installation Precautions Other PrecautionsEnvironment Power Supply/Grounding the Machine Handling of Plastic Bags Precautions for Use Xxiii Xxiv Xxv Xxvi Guide to the Operation Guide Convention Description Example ConventionsMachine Parts 1112 110 1314 Components at the Front of the PrinterComponents at the Left and the Rear of the Printer Components at the Right of the Printer Printing Operation Loading Printer Driver Printing from Application Software Operation Guide Maintenance General Information Toner Kits Toner Container ReplacementFrequency of toner container replacement Starter Toner ContainerReplenishing Toner Gently lift the toner container Times or more to loosen and mix the toner inside Replacing the Waste Toner Box Peel sticker a off the waste toner box Operation Guide Operation Guide Cleaning the Filters Cleaning the PrinterOperation Guide Inside of the Printer With the separator Troubleshooting General Guideline Symptom Check Items Corrective ActionTips Printed Results Corrective Action Print Quality ProblemsCheck the EcoPrint setting Check the paper ramp Indicator Condition Description Indicators and MessagesIndicators Maintenance Messages0123456 Message Corrective Action Missing Image adapt Error MessagesKpdl Print overrun Paper jam message Description Reference Location Correcting a Paper JamOnline help messages LocationPaper Cassette Inside the MP transport MP TrayOperation Guide Transport tray section Operation Guide Jam in Left Cover Left Cover Document Finisher Operation Guide Description FS-9130DN FS-9530DN SpecificationsFS-9130DN FS-9530DN FS-9130DN FS-9530DN Operation Guide Page Page Page Rev .3 2007.7 302G156012
Related manuals
Manual 2 pages 5.54 Kb Manual 2 pages 23.58 Kb

FS-9130DN, FS-9530DN specifications

The Kyocera FS-9130DN is a robust monochrome laser printer designed for medium to large workgroups that require high-performance printing solutions. Renowned for its efficiency and productivity, the FS-9130DN stands out in a competitive market, thanks to its advanced features and technologies.

At the heart of the FS-9130DN is Kyocera's innovative Ecosys technology. This technology not only contributes to lower total cost of ownership but also promotes eco-friendliness without compromising performance. The printer utilizes a long-life drum and toner system, significantly reducing consumable replacements and waste. This means users can print more pages per cartridge, which is both cost-effective and environmentally responsible.

A standout feature of the FS-9130DN is its impressive print speed. Capable of producing up to 50 pages per minute (ppm), this printer excels in scenarios where large volumes of documents need to be printed quickly and efficiently. Additionally, it supports automatic duplex printing, which allows users to print on both sides of a page without manual intervention, thus saving paper and enhancing productivity.

The FS-9130DN also boasts a high maximum monthly duty cycle of up to 250,000 pages, making it an ideal choice for busy office environments. The printer is equipped with a standard paper capacity of 600 sheets, which can be further expanded with optional trays, allowing for a maximum input capacity of up to 2,600 sheets. This extensive paper handling capability minimizes interruptions for paper reloads during each workday, allowing staff to focus on critical tasks.

Another key characteristic of the FS-9130DN is its versatility in connectivity options. The printer supports USB, Ethernet, and optional wireless connectivity, facilitating seamless integration into various office setups. In addition, it is compatible with mobile printing solutions, enabling users to print directly from smartphones and tablets for added convenience.

The device also features an intuitive control panel, providing users with easy access to various functions and settings. Furthermore, the FS-9130DN incorporates advanced security features, ensuring that sensitive documents remain protected in a corporate environment.

In conclusion, the Kyocera FS-9130DN is a powerful monochrome printer that combines cutting-edge technology, high-speed performance, and extensive paper handling capabilities. Its focus on efficiency and sustainability, coupled with versatile connectivity options, makes it an excellent choice for organizations seeking a reliable and cost-effective printing solution.
Top Page Image Contents