Lexmark 5200 manual Setup Troubleshooting, Have a question?, Need more ink?

11	Press	to print
	an alignment page.

You may discard the alignment page after it prints.

12

If you are using your All-In-One without a computer, you are finished.

If you are using your All-In-One with a computer, continue to step 12.

Make sure your	13 Connect the USB cable.
computer is on.

14 Important!

Click Cancel on all New Hardware screens.

Windows 98/Me

Windows 2000/XP

Note: New Hardware screens appear only for Windows users. For Macintosh, continue to step 15.

Insert the CD. Follow the

15 instructions on your computer screen.

If you inserted the CD and the install screen did not appear (Windows):

1Click Cancel on any New Hardware screens.

2Eject and reinsert the All-In-One software CD.

If the All-In-One software install screen does not appear:

a From your desktop, double-click My Computer (In Windows XP, click Start à My Computer).

b Double-click the CD-ROM drive icon. If necessary, double-click setup.exe. c When the All-In-One software installation screen appears, click Install.

d Follow the instructions on the screen.

If you inserted the CD and the install screen did not appear (Mac):

1From your desktop, double-click the Lexmark 5200 Series Installer icon.

2Double-click Install and follow the instructions on the screen.

Setup Troubleshooting

Symptom:	Diagnosis:	Solution:
The Power light is	Is the power cord pushed all	Disconnect the power cord from
not lit	the way into the All-In-One?	the wall outlet, and then from
		the All-In-One. Reconnect the
		power cord by pushing it all the
		way into the connector on the
		All-In-One, and then into the
		wall outlet.
	Is the All-In-One connected to	Connect the All-In-One to an
	a working electrical outlet?	electrical outlet that other
		electrical devices have been
		using.
Software will not	Is your operating system	The All-In-One supports these
install	compatible with the All-In-	operating systems:
	One?	•	Windows 98
		•	Windows Me
		•	Windows 2000
		•	Windows XP
		• Mac OS X version 10.1.5
		• Mac OS X version 10.2.3 and
			later
Alignment page or	Is the All-In-One on?	Press the Power button. If the
test page will not		Power light does not come on,
print		see the “The Power light is not
		lit” symptom at the beginning of

Have a question?

•Refer to your User’s Guide.

•Visit our Web site: http://support.lexmark.com/.

•Call us at 1-800-332-4120. Monday-Friday (9:00 AM - 9:00 PM EST) Saturday (Noon-6:00 PM EST)

Note: Phone number and support times may change without notice.

Record the following information (located on your store receipt and the back of your printer) and have it ready when you contact us so that we may serve you faster:

Machine Type number

Serial number

Date purchased

Store where purchased

Need more ink?

The following cartridges work with your printer.

• 31	•	32	•	33
	•	34	•	35

		this table.
	Do you see an error	See “Error messages
	message?	troubleshooting” in your User’s
		Guide.
	Is your All-In-One connected	Disconnect the USB cable from
	to your computer through	any other devices and directly
	another device, such as a	connect it between the All-In-
	USB hub or switch box?	One and your computer. For
		help, see step 13.
	Did you remove the sticker	Remove the print cartridges,
	and tape from the bottom of	check for the sticker and tape
	each print cartridge?	and then reinsert them. For
	Are the print cartridges	help, see step 8 and step 9.
	installed properly?
	Is the paper loaded correctly? See step 6.
The control panel	Did you select a language?	1 Press the Power button to
displays text in the		turn on the All-In-One.
wrong language		2 Press and hold both the
		Power and Cancel buttons
		for 10 seconds. Language
		text appears on the display.
		3 Press the + button repeatedly
		until the language you want
		appears on the display.
		4 Press the Arrow button to
		select that language.

P/N 21D0070 E.C. 21D005

© 2004 Lexmark International, Inc. All rights reserved.