Philips 245P2 Auto button doesnt function, Auto function is applicable only, Troubleshooting

Page 52

7.

Troubleshooting & FAQs

AUTO button doesn't function

• The auto function is applicable only in

 

 

 

 

 

VGA-Analog mode. If the result is not

7.1

Troubleshooting

 

satisfactory, you can do manual adjustments

This page deals with problems that can be

 

via the OSD menu.

 

 

corrected by a user. If the problem still persists

 

Note

after you have tried these solutions, contact Philips

 

The Auto Function is not applicable in

customer service representative.

 

DVI-Digital mode as it is not necessary.

 

 

Common Problems

Visible signs of smoke or sparks

 

 

No Picture (Power LED not lit)

• Do not perform any troubleshooting steps

• Disconnect the monitor from mains power

•

Make sure the power cord is plugged into the

 

source immediately for safety

 

 

power outlet and into the back of the monitor.

• Contact with Philips customer service

•

First, ensure that the power button on the

 

representative immediately.

 

 

front of the monitor is in the OFF position,

 

 

 

 

then press it to the ON position.

 

Imaging Problems

 

 

 

No Picture (Power LED is white blinking)

Image is not centered

•

Make sure the computer is turned on.

• Adjust the image position using the “Auto”

•

Make sure the signal cable is properly

 

function in OSD Main Controls.

 

 

connected to your computer.

• Adjust the image position using the Phase/

•

make sure the monitor cable has no bent pins

 

Clock of Setup in OSD Main Controls. It is

 

 

on the connect side. If yes, repair or replace

 

valid only in VGA mode.

 

 

the cable.

 

 

•

The Energy Saving feature may be activated

Image vibrates on the screen

Screen says

• Check that the signal cable is properly securely

 

connected to the graphics board or PC.

 

 

 

 

Vertical flicker appears

•

Make sure the monitor cable is properly

 

 

 

 

connected to your computer. (Also refer to

 

 

 

 

the Quick Set-Up Guide).

• Adjust the image using the “Auto” function in

•

Check to see if the monitor cable has bent

 

OSD Main Controls.

 

 

pins.

• Eliminate the vertical bars using the Phase/

•

Make sure the computer is turned on.

 

Clock of Setup in OSD Main Controls. It is

 

 

 

 

 

valid only in VGA mode.

50

Page 51 Page 53
Image 52
Page 51 Page 53
Contents 245P2 Table of Contents Temperature 0-40C 32-95F Humidity 20-80% RH Safety precautions and maintenanceOperation Notational Descriptions Weee Setting up the monitor Installation Package contentsUSB upstream and downstream Kensington anti-thief lock Main menu Sub menu Physical Function Pivot Tilt Resolution notificationSwivel Remove the 4 screw covers How to enable SmartImage? Why do I need it?Except using key to scroll down, you can also How does it work?Off No optimization by SmartImage What is it? Philips SmartControl Premium First launch -WizardPage Page ECO Page OptionAuto Pivot Facoty Preset can also be called from the drop down menu Task Tray Menu Enabled Other alternative path Vista Drag and Drop WindowsWin No other alternative path available Title Bar Options Display Tune from the start menu or short cut on the desktopLeft Click Menu SmartDesktop Partition Definitions Horizontal Split Top Left side VerticalRight side Vertical Right side Vertical Even SplitSettings Default settings PowerSensorCustom settings Philips Flat Panel Monitors Pixel Defect Policy Pixels and Sub pixelsTypes of Pixel Defects Bright Dot DefectsModel TFT-LCD CcflYES USBMtbf Environmental Rohs YES EpeatAutomatic PowerSaving Power Management DefinitionLead-free Product Epeat Electronic Product2006/95/EC Low Voltage Directive 2004/108/EC EMC Directive Benefits of EpeatProduct also comply with the following standards Federal Communications Commission FCC Notice U.S. Only Reorient or relocate the receiving antennaCommission Federale de la Communication FCC DeclarationPolish Center for Testing and Certification Notice Paikka/IlmankiertoVaroitus Plassering/VentilasjonErgonomie Hinweis nur Deutschland Achtung Beim AufstellenEastern Europe Latin AmericaNorth America PacificWhat is excluded? Page Dear Customer Just a click away Just a phone call awayEstonia Fujitsu Services OU BelarusBulgaria Czech RepublicRomania Turkey Serbia & MontenegroUkraine SlovakiaCompany Name PT. Gadingsari elektronika Prima Africa South AfricaAfter service hours until Service hours Sun.~ThursTo the service provider at your expense Limited Warranty Computer MonitorWHO is COVERED? What is COVERED? What is EXCLUDED?Your warranty does not cover Where can I GET More INFORMATION?To GET Warranty Service in Canada Your International Guarantee Dear Customer Troubleshooting This page deals with problems that can be Via the OSD menuCustomer service representative Source immediately for safetyPower on light is too strong and is Disturbing Reconnect your USB peripheralsSmartControl Premium FAQs Page Icm? Q4 How do I adjust the resolution? Q7 How should I clean the LCD surface? Q9 Can the Philips LCD Monitor be mounted on the wall?
Top Page Image Contents