Philips 231T1 Product information, Tuner/Reception Transmission, Power, Supported TV mounts

Page 16

6Product information

Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.

Supported display resolutions

Computer formats

Resolution - refresh rate:

640 x 480 - 60Hz

640 x 480 - 75Hz

800 x 600 - 60Hz

800 x 600 - 75Hz

1024 x 768 - 60Hz

1024 x 768 - 75Hz

1280 x 1024 - 60Hz

1440 x 900 - 60Hz

1600 x 900 - 60Hz (the best for

201T1)

1680 x 1050 - 60H z

1920 x 1080 - 60Hz_RB (the best for 221T1 and 231T1)

Video formats

Resolution - refresh rate:

480i - 60Hz

480p - 60Hz

576i - 50Hz

576p - 50Hz

720p - 50Hz, 60Hz

1080i - 50Hz, 60Hz

1080p - 50Hz, 60Hz

Tuner/Reception/

Transmission

Antenna input: 75ohm coaxial (IEC75)

DVB: DVB Terrestrial, DVB-T MPEG4

TV system: DVB COFDM 2K/8K; PAL I, B/G, D/K; SECAM B/G, D/K, L/L’

Video playback: NTSC, SECAM, PAL

Tuner Bands: Hyperband, S-channel,

UHF, VHF

Remote control

Type: 201T1, 221T1, 231T1 RC

Batteries: 2 x AAA (LR03 type)

Power

Mains power: 100-240V, 50Hz

Off mode power: < 0.5W

Ambient temperature: 5 to 40 degrees Celsius

Supported TV mounts

To mount the TV, purchase a Philips TV mount or a VESA-compatible TV mount.To prevent damage to cables and connectors, be sure to leave a clearance of at least 5.5 cm from the back of the TV.

Warning

•• Follow all instructions provided with the TV mount. Koninklijke Philips Electronics N.V. bears no responsibility for improper TV mounting that results in accident, injury or damage.

TV screen

Required

Required

size (inches)

pitch (mm)

mounting bolts

20

100 x 100

4 x M4

22

100 x 100

4 x M4

23

100 x 100

4 x M4

14EN

Image 16
Contents 201T1 221T1 231T1 Register your product and get support atModel Contents Koninklijke Philips Electronics N.V. All rights reserved Copyright Safety Risk of electric shock or fireScreen care Get started and connect your devices Back connectorPC in VGA and Audio Audio and video input from a computer Audio and video output to analogue DeviceSide connector Slot for a Conditional Access Module CAMUSB port, for upgrade firmware purpose only Audio input from analogue devices connected to VideoControls Remote controlFront and side controls Toggle to select the Smart Picture setting Switch the Electronic Programme Guide On or OffPress to switch to Video YPbPr Composite /SCART mode Toggle to select the Smartsound ModePress to display the Favourite List Press to display the index page of TeletextPress to display the Channel List Switch your TV on/off or to standby Switch channelsTo switch on Start to useWatch connected devices Adjust TV volume Use the source buttonPower Product informationTuner/Reception Transmission Supported TV mountsTV/Channel settings Using TV signal as the input sourceSettings Audio CarrierAnalog TV only1st Audio and 2nd Audio Digital TV only Channel ScanUpdate Scan Single RF Scan Digital TV onlyChannel Skip Analog Manual Scan Analog TV onlyPress OK button to set. a checked icon is a skip one Channel Sort Swap Channel EditAnalog Ch Fine Tune Analog TV only Decoder Analog TV onlyAppendix Feature setting highlights Using the TeletextParental Menu setting Using the EPGChannel Block Input Block Parental GuidanceAge Rating Set Password Clean AllOAD update Pixel policyPixel Defect Tolerances Defects Proximity of Pixel DefectsTolerances listed in the following tables Total bright dot defects of all types Dark subpixelAdjacent dark subpixels Total black dot defects of all typesTroubleshooting General TV issuesTV channel issues Picture issuesSound issues Hdmi connection issuesComputer connection issues OthersContact us
Related manuals
Manual 21 pages 60.7 Kb