Philips 222E2SB/00, 222EL2 user manual Troubleshooting, No Picture Power LED not lit, Screen says

Page 44

7 Troubleshooting & FAQs

7.1 Troubleshooting

This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.

Common Problems

No Picture (Power LED not lit)

Make sure the power cord is plugged into the power outlet and into the back of the monitor.

First, ensure that the power button on the front of the monitor is in the OFF position, then press it to the ON position.

No Picture (Power LED is white blinking)

Make sure the computer is turned on.

Make sure the signal cable is properly connected to your computer.

make sure the monitor cable has no bent pins on the connect side. If yes, repair or replace the cable.

The Energy Saving feature may be activated

Screen says

Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Set-Up Guide).

Check to see if the monitor cable has bent pins.

Make sure the computer is turned on.

AUTO button doesn't function

The auto function is applicable only in VGA-Analog mode. If the result is not satisfactory, you can do manual adjustments via the OSD menu.

Note

The Auto Function is not applicable in DVI-Digital mode as it is not necessary.

Visible signs of smoke or sparks

Do not perform any troubleshooting steps

Disconnect the monitor from mains power source immediately for safety

Contact with Philips customer service representative immediately.

Imaging Problems

Image is not centered

Adjust the image position using the “Auto” function in OSD Main Controls.

Adjust the image position using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image vibrates on the screen

Check that the signal cable is properly securely connected to the graphics board or PC.

Vertical flicker appears

Adjust the image using the “Auto” function in OSD Main Controls.

Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

42

Image 44
Contents 222EL2 222E2 Table of Contents Operation Safety precautions and maintenanceTemperature 0-40C 32-95F Humidity 20-80% RH Notational Descriptions Weee Installation Package contents Install base standPage Basic and simple instruction on the control keys Main menu Sub menuResolution notification 100mm How does it work? SmartImage Lite What is it?Why do I need it? There are 3 modes to be selected Standard Internet, and Game Philips SmartControl Lite Start with Standard pane Adjust menu Color menu Next goes to the succeeding target 6-targets Page Page Task Tray Menu Enabled Philips Flat Panel Monitors Pixel Defect Policy Pixels and Sub pixelsTypes of Pixel Defects Bright Dot DefectsModel YES Picture/Display LCD panel typeTFT-LCD Power 222E2 On mode typical 40W Energy Consumption Mtbf 50,000 hrs 222E2, 30,000 hrs 222EL2Environmental Rohs YES EpeatAutomatic PowerSaving Automatic power saving feature Power Management DefinitionLead-free Product Epeat Electronic ProductProduct also comply with the following standards Benefits of Epeat2006/95/EC Low Voltage Directive 2004/108/EC EMC Directive Federal Communications Commission FCC Notice U.S. Only Reorient or relocate the receiving antennaCommission Federale de la Communication FCC DeclarationPolish Center for Testing and Certification Notice Paikka/IlmankiertoVaroitus Plassering/VentilasjonErgonomie Hinweis nur Deutschland Achtung Beim AufstellenEastern Europe Latin AmericaNorth America PacificWhat is excluded? Page Dear Customer Just a click away Just a phone call awayEstonia Fujitsu Services OU BelarusBulgaria Czech RepublicRomania Turkey Serbia & MontenegroUkraine SlovakiaCompany Name PT. Gadingsari elektronika Prima Africa South AfricaPage WHO is COVERED? What is COVERED? What is EXCLUDED?Your warranty does not cover Where can I GET More INFORMATION?To GET Warranty Service in Canada Your International Guarantee Dear Customer Screen says TroubleshootingNo Picture Power LED not lit Power on light is too strong and is Disturbing Green, red, blue, dark, and white dots appears on the screenSmartControl Lite FAQs Page Q9 Can the Philips LCD Monitor be mounted on the wall? Q7 How should I clean the LCD surface?Color TemperatureThe 2 settings are 6500K, and 9300K