Philips BDL4220QL user manual Safety Instructions, Know These Safety Symbols, Information Display

Page 2

BDL4220QL

Safety Instructions

TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC

 

 

 

 

 

 

 

 

SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN

Warnings and Precautions

OR MOISTURE.

The Socket-outlet should be installed near the apparatus and be easily

 

KNOW THESE SAFETY SYMBOLS

 

accessible.

 

 

 

 

 

 

 

 

Read and follow these instructions

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

when connecting and using your Public

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Information Display:

 

 

 

 

 

 

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

CAUTION: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it.

CAUTION: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

Unplug the display if you are not going to use it for an extensive period of time.

Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off.

However, never use alcohol, solvents or ammonia-based liquids.

Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.

The casing cover should be opened only by qualified service personnel.

Keep the display out of direct sunlight and away from stoves or any other heat sources.

Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.

Do not block the ventilation holes on the cabinet.

Keep the display dry.To avoid electric shock, do not expose it to rain or excessive moisture.

If turning off the display by detaching the power cable, wait for 6 seconds before re-attaching the power cable for normal operation.

To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture.

When positioning the display, make sure the power plug and outlet are easily accessible.

IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen.This is a well-known phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the afterimage will disappear gradually over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not covered under warranty.

ii

Image 2
Contents BDL4220QL When connecting and using your Public Safety InstructionsKnow These Safety Symbols Read and follow these instructionsImportant Safety Instructions Federal Communications Commission FCC Notice U.S. Only Regulatory InformationCE Declaration of Conformity Information for U.K. only Polish Center for Testing and Certification NoticeHow to connect a plug Electric, Magnetic and Electronmagnetic Fields EMFChina RoHS 中国电子信息产品污染控制标识要求Waste Electrical and Electronie Equipment North Europe Nordic Countries InformationEnd-of-Life Disposal VarningTable Of Contents Installation Notes Unpacking and InstallationPackage Contents UnpackingMounting on a Wall Ventilation Requirements for enclosure locatingControl Panel Remote control sensor and power status indicatorParts and Functions ButtonInput/Output Terminals List Remote ControlGeneral functions OptionsOperating range of the remote control Inserting batteries in the remote controlHandling the remote control Connecting External Equipments Connection1. RS232C control connection optional Connecting Multiple DisplaysIR Pass-through Connection optional IR connection optionalWire-connecting to Network optional To setup the networkOperation Playing music files Play optionsPlay multimedia files from USB device Movie options Playing movie filesPlaying photo files Start a slideshowUsing the remote control Change your settingsSettings Quick Picture and SoundSound menu Digital Crystal ClearNetwork Settings General settings menuSdtv Resolution Input modePC Resolution Hdtv ResolutionTypes of Pixel Defects + Dot Definition Pixel Defect PolicyPixels and Sub-pixels Bright Dot DefectsPixel Defect Tolerances Dark Dot DefectsProximity of Pixel Defects MuraFront Panel Cleaning Instructions Cleaning and TroubleshootingCleaning Cabinet Cleaning InstructionsTroubleshooting Symptom Possible Cause RemedyIn/Out Terminals Technical SpecificationsDisplay General