Philips 107B7 manual Ray protection, Quartz Oscillatorpin45,pin46, + Control Function Block

Page 23

17” CDT Color Monitor

107B7

x-ray protection

The x-ray protection(pin22) input XRAY provides a voltage detector with a precise voltage input for X-ray protection .If the input voltage at XRAY exceeds the upper threshold for 150us to 300us,the system is forced to shut down by switching off vertical-and B-drive signals. There are two different ways to handle the system in case of XRAY occurrence:

1.If the x-ray latch enable bit UCXRAY[2] was set to “0” during startup the system will shut down without any interference of the uC.The deflection controller is set to ldle mode. Restart of the system only possible due to seitching power off/power on.

2.If register bit UCXRAY[2] was set to “1”,micro controller interaction is allowed .If the micro controller doesn’t interrupt the system, the system will shut down to ldle mode. For any interaction of the micro controller the XRAY occurrence has to be acknowledged by the micro controller by clearing the bit SY-STATUS[2].The micro controller take over the control of the handling via software. The actual x-ray pin status can be read through bit SY-STATUS[1].

Quartz Oscillator(pin45,pin46)

The quartz oscillator circuit is available on pins XTAL1(input) and XTAL2(output) and works together with an external 48MHz 3rd overtone quartz. As a result the quartz oscillator is always running on 48MHz.Other quartz crystal frequencies than 48 MHz cannot be used.External capacitors on XTAL1 and XTAL2 are not allowed.

B+ Control Function Block

The B+control block of the SAA4849 has the same behaviour as the TDA4856 with adapted threshol voltages.The circuit allows the user to choose the trigger edge of the HDRV signal and the polarity of the output stage via I2C-Bus.

The B+ control function block of the SAA4849 consists of an Operational Transconductance Amplifier(OTA), a voltage comparator,a flip-flop and a discharge circuit. This configuration allows easy application for different B+ control concepts.

HPLL

The horizontal part contains a PLL,which works over the full frequency range from 25kHz to 140 kHz.This range can be reduced by a ower and an upper frequency limit(Write Once Registers HPMAX and HPMIN).Via I2C bus the number of 48MHz clock cycles is sent through the register. The slewing speed during mode change is also programmable in a write once register (HSLEW)

After the clocks for the HPLL are switched on, the HPLL starts with a fixed freerunning frequency of 60 kHz.The H-drive pulses are not active and the start up procedure is inhibited.The default setting of register bit HCONTROL [0] will cause the HPLL to slew ,not switch.to the freerunning frequency defined in the I2C register HPFREE( the default value is also 60 kHz).Independent on H-syncs which are possibly present.the HPLL will slew to that freerunning frequency. To achieve an always defined starting point for the startup procedure,this procedure cannot be interrupted.

23

Image 23
Contents Service Revision History Revision ListFor Products Containing Laser CDT Color Monitor 107B7 Important Safety Notice.POWER Consumption Monitor SpecificationsInternational Regulatory Specification Singapore CanadaRED CRT Mexico KoreaSafety precautions Precautions and noticesHigh voltage warning CDT Color Monitor 107B7 Product safety noticeService notes GND Operating instructionsPin No Description Main adjustments AdjustmentAdjustment conditions and precautions OSD Tree Basic and simple instruction on the control keysCDT Color Monitor 107B7 CDT Color Monitor 107B7 Adjustment method CDT Color Monitor CDT Color Monitor 107B7 Relative placement of typical components System and equipment requirements Take 105G7 DDC writer for example 1.GeneralSUB connector Printer connector DC 12V input CDT Color Monitor 107B7 Enter, go into the next screen as shown Fig Enter into Fig Micro controller and deflection circuit Micro Controller Sync signals processorReset Circuitpin23 Circuit description+ Control Function Block Ray protectionQuartz Oscillatorpin45,pin46 Location Description Function CDT Color Monitor 107B7 Transistor & Diode and IC CircuitGeneral Mechanical InstructionsMain panel Remove Main board Remove Front frame No Raster Trouble Shooting ChartCRT Relative Circuit Problems Abnormal DDC Plug & Play Abnormal Video Level On ScreenCDT Color Monitor 107B7 Abnormal Display No Signal On ScreenCDT Color Monitor 107B7 No Blanking Hor./Osc/Def/Hv Circuit FaultNo Raster Disconnect With Signal Cable Abnormal Horizontal Linearity CDT Color Monitor 107B7 Abnormal Horizontal DeflectionAbnormal Horizontal Width Of Video Abnormal Vertical Size CDT Color Monitor 107B7 Abnormal Vertical ScanningSide-Pin Cushion Distortion Poor FocusCDT Color Monitor 107B7 Power Supply Trouble Shooting Chart Mechanical of cabinet front dis-assembly Spare parts List Location Part No. for TPV Description Philips P/N 12NC Main BoardFerrite Bead WireWIRE&CORE Ferrite Bead 3*5*1.5Mgfr 240K OHM Mofr 0.75 OHMMgfr 270K OHM Mgfr 470KOHMCFR 6.2K OHM CFR 4.7 OHMCFR 5.6K OHM CFR 56K OHMCFR 8.2K OHM CFR 2.2K OHMCFR 2.4K OHM CFR 470 OHMCFR 1.5 OHM CFR 1K OHMCFR 1M OHM CFR 120 OHMNPO Key Board Location Part No for TPV Description Philips 12NC CRT Board Location Part No for TPV Description Philips 12NC BAV21 CFR 560K OHMTZX8V2B Different parts listPower Cord Signal CablePincushion Size Control Blanking Circuit Block diagramIC Block diagram SAA4849 IC102 M24C08 IC801 NT6812 GND Gnds N/C N/C VCC Main Board PCB LayoutCDT Color Monitor 107B7 Video Board Schematic diagram Output Power107B7 Video General Product Specification PHL General Product FeaturesScope Destination Mains Magnetic Cabinet Cord Standard Testing ConditionsVideo Signals Video Input Signals Product RangePlug And Play Video Driver SignalsDDC Signals Preset & Preload Modes Timing Chart Preset video timingsFrequency 31.469 kHz 43.269 kHz 31.468 kHz Total Timing Resolution 640 x 720 x Pixel clockSync Polarity Timing Resolution 800 x 1024 x Pixel clock Polarity Timing Resolution 1024 x 1280 x Pixel clockFrequency 31.469 kHz 37.500 kHz 50.628 kHz Total Timing ResolutionSync Polarity Timing Resolution Polarity Timing ResolutionPower consumption Timing Resolution 1152 x 1280 x Pixel clockPolarity Timing Resolution 1280 1600 x Pixel clock Polarity Power Supply 2.6.1 FeaturesKey R to L Function Power saving conditionsOSD tree / English 1st level 2nd level 3rd level LED indicatorOSD menu Monitor status information Power connectorVideo input connector/Video cable Front Of Screen Performance CRT characteristicsPhosphor Area VendorCRT Type Number Screen & Mask Screen Diagonal SizeOptical performance Location of icons Accessories CablesUser’s manual CD-ROMIf paint is used Texture/Glossing of housingColor for resin/paint ResinsLabel Product Dimensions / WeightTransportation test procedures Movement of unit with base16.2. Sea shipment container loading for China & India Pallet / Container loading16.1. Air shipment container loading Reliability / Environment / Transportation Temperature16.3. Sea shipment container loading for other regions 16.4. Truck loading for ChinaSouth Hemispheric AltitudeAir pressure Earth magnetic field North HemisphericNEW-ZEALAND Israel Sa = SafetyRED CRT Dnhw Mexico Weee MPR II / TCO107B70 Grey 107B75 RoHS TCO-99 TCO-03

107B7 specifications

The Philips 107B7 is a well-regarded monitor designed for users who prioritize both performance and health in their computing experience. Aimed at professionals and home users alike, this monitor integrates advanced technologies that enhance productivity while promoting eye comfort.

One of the standout features of the Philips 107B7 is its commitment to Eye Care technology. This monitor incorporates a range of innovations specifically designed to reduce eye strain, such as LowBlue Mode and Flicker-free technology. LowBlue Mode reduces the amount of harmful blue light emitted by the screen, which is known to cause discomfort during prolonged use. Flicker-free technology, on the other hand, eliminates flickering at all brightness levels, providing a stable image that helps prevent fatigue.

The monitor boasts a 21.5-inch display with a resolution of 1920 x 1080 pixels, delivering sharp and vibrant visuals. This Full HD resolution ensures that users can enjoy crisp images whether they’re working on spreadsheets, watching videos, or designing graphics. Additionally, the panel features wide viewing angles, which means that colors remain consistent even when viewed from off-angles, making it ideal for collaborative work.

In terms of connectivity, the Philips 107B7 offers a variety of options. Users can easily connect their devices via HDMI, DisplayPort, and VGA inputs. The inclusion of USB ports is also a significant advantage, allowing for easy connection of peripherals like keyboards, mice, and other accessories.

Another notable aspect of the Philips 107B7 is its ergonomic design. The monitor features a height-adjustable stand that enables users to customize the screen's position for optimal viewing comfort. This flexibility aids in maintaining good posture and reducing strain during long working hours.

With its sleek design and adaptive technologies, the Philips 107B7 is more than just a monitor; it is a tool for enhancing productivity while keeping health and comfort at the forefront. Whether for office use, creative tasks, or leisurely activities, this monitor is designed to meet a variety of needs in today’s dynamic workspace. By combining advanced features with user-friendly design, the Philips 107B7 stands out as a strong choice for anyone looking to upgrade their viewing experience.