Philips CBT6800 manual AC Characteristics, AC Waveforms, Test Circuit and Waveforms, Input Output

Page 5

Philips SemiconductorsProduct data

10-bit bus switch with precharged outputs

 

 

 

CBT6800

for live insertion

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AC CHARACTERISTICS

 

 

 

 

 

 

 

 

GND = 0 V; CL = 50 pF; tr = tf 2.5 ns

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LIMITS

 

 

 

 

FROM

TO

 

 

 

 

SYMBOL

PARAMETER

VCC = +5.0 V

±0.5 V

UNIT

(INPUT)

(OUTPUT)

 

 

 

 

 

 

Min

 

Max

 

 

 

 

 

 

 

 

 

 

 

t

Propagation delay1

A or B

B or A

 

.25

ns

pd

 

 

 

 

 

 

 

 

 

tPZH

BIASV = GND

 

 

 

A or B

2.4

 

7.7

ns

 

ON

TPZL

BIASV = 3 V

 

 

 

 

3.0

 

8.3

 

tPHZ

BIASV = GND

 

 

 

A or B

1.0

 

5.3

ns

 

ON

TPLZ

BIASV = 3 V

 

 

 

 

3.1

 

7.8

 

NOTE:

1.This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical on-state resistance of the switch and a load capacitance of 50 pF, when driven by an ideal voltage source (zero output impedance).

AC WAVEFORMS

VM = 1.5 V, VIN = GND to 3.0 V

 

 

3 V

1.5V

1.5V

INPUT

 

 

0 V

tPLH

tPHL

 

VOH

1.5V

1.5V

OUTPUT

VOL

 

 

SA00028

Waveform 1. Waveforms Showing the Input (An) to Output (Yn)

Propagation Delays

TEST CIRCUIT AND WAVEFORMS

 

 

7 V

From Output

500

S1

 

Open

Under Test

 

 

GND

 

 

CL = 50 pF

500

 

 

 

 

Load Circuit

 

TEST

S1

 

tpd

open

 

tPLZ/tPZL

7 V

 

tPHZ/tPZH

open

DEFINITIONS

CL = Load capacitance includes jig and probe capacitance; see AC CHARACTERISTICS for value.

Output Control (Low-level enabling

tPZL

Output

Waveform 1

S1 at 7 V

(see Note)

tPZH

Output

Waveform 2

S1 at Open

(see Note)

1.5 V

tPLZ

1.5 V

tPHZ

1.5 V

3V

1.5 V

0V

3.5V

VOL + 0.3V

VOL

VOH

VOH - 0.3V

0V

SA00012

NOTES:

1.All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2.5 ns, tf 2.5 ns.

2.The outputs are measured one at a time with one transition per measurement.

Note:

Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.

Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.

SA00029

Waveform 2. Waveforms Showing the 3-State Output Enable

and Disable Times

2003 Sep 12

5

Image 5
Contents CBT6800 PIN Configuration FeaturesDescription Quick Reference DataFunction Table Logic SymbolAbsolute Maximum RATINGS1 Recommended Operating ConditionsMin DC Electrical CharacteristicsParameter Test Conditions From Symbol Parameter AC CharacteristicsAC Waveforms Test Circuit and WaveformsPhilips Semiconductors Supersedes data of 28 October 1999 9397 750 Revision HistoryRev Date Description Definitions Data sheet statusDisclaimers Contact information