Black Box LGB6000SC-004, LGB6001C, LGB6000SC-001, LGB6026A Power Cord Safety, France and Peru only

Page 8

COMPLIANCES AND SAFETY STATEMENTS

POWER CORD SAFETY

Please read the following safety information carefully before installing the switch:

WARNING: Installation and removal of the unit must be carried out by qualified personnel only.

The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.

Do not connect the unit to an A.C. outlet (power supply) without an earth (ground) connection.

The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN 60320/IEC 320 appliance inlet.

The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.

This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.

France and Peru only

This unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio

1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground).

†Impédance à la terre

IMPORTANT! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:

– 8 –

Image 8

Contents Customer Support Information Blackbox.com Blackbox.com INS Tallation Guide Compliances and Safety Statements FCC Class aIndustry Canada Class a Japan Vcci Class aCE Mark Declaration of Conformance for EMI and Safety EEC Safety Compliance PSE a LarmPower Cord Safety France and Peru onlyPower Cord Set France et Pérou uniquement Sein und die Aufschrift HAR oder Basec tragen Environmental Statements END of Product Life Span Compliances and Safety Statements About this Guide PurposeAudience ConventionsRevision History Contents Troubleshooting SpecificationsMaking Network Connections CablesTables Tables Figures Figures Introduction OverviewSwitch Architecture LGB6050ASFP Transceiver Slots Description of HardwareNetwork Management Options Port and System Status Leds Gigabit Ethernet Module SlotsStacking Ports System LEDs Chapter Optional Redundant Power SupplyPower Supply Socket 10GBASE SFP+ Module Features and Benefits ConnectivityExpandability PerformanceManagement Introduction Introduction to Switching Network PlanningApplication Examples Collapsed BackboneNetwork Aggregation Plan Network Aggregation PlanRemote Connections with Fiber Cable Remote Connections with Fiber CableMaking Vlan Connections Making Vlan ConnectionsUsing Layer 3 Routing IP Routing for Unicast TraffiApplication Notes Network Planning Installing the Switch Selecting a SiteEthernet Cabling RJ-45 ConnectionsOptional RACK-MOUNTING Equipment Equipment ChecklistPackage Contents Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetInstalling AN Optional Module Into the Switch Installing an Optional ModuleInstalling AN Optional SFP Transceiver Inserting an SFP Transceiver into a SlotConnecting Switches in a Stack Stacking Topologies Making Stacking ConnectionsConnecting to a Power Source Power SocketConnecting to the Console Port Wiring MAP for Serial CableInstalling the Switch Installing the Switch Connecting to the Console Port Connecting Network Devices Making Network ConnectionsTWISTED-PAIR Devices Cabling GuidelinesConnecting to PCS, SERVERS, Hubs and Switches Making Twisted-Pair ConnectionsNetwork Wiring Connections Network Wiring Connections Fiber Optic SFP DevicesMaking Fiber Port Connections Making Network Connections Gbps Fiber Optic Connections Connecting to an SFP+ Transceiver Gbps Ethernet Collision Domain Connectivity Rules1000BASE-T Cable Requirements Micron single 40 km 24.85 miles Mode fiber Cable Labeling and Connection Records Mbps Ethernet Collision DomainMaking Network Connections Troubleshooting Diagnosing Switch IndicatorsDiagnosing Power Problems with the Leds RPU LEDIN-BAND Access Power and Cooling ProblemsInstallation Stack Troubleshooting Cables TWISTED-PAIR Cable and PIN AssignmentsSTRAIGHT-THROUGH Wiring 10BASE-T/100BASE-TX PIN AssignmentsCrossover Wiring Straight-through WiringCable Testing for Existing Category 5 Cable 1000BASE-T PIN AssignmentsAdjusting Existing Category 5 Cabling to RUN 1000BASE-T Fiber StandardsNon-Zero Dispersion-Shifted Specifications Physical CharacteristicsPorts Network InterfaceLeds AC InputSwitch Features Management Features StandardsIN-BAND Management OUT-OF-BAND ManagementCE Mark 10GBASE Extender Module SFP+Compliances Standards Glossary CSMA/CD 10GBASE-LR10GBASE-SR Ieee EthernetFast Ethernet FULL-DUPLEXLED MIBVirtual LAN Vlan TIAUTP Glossary Index NumericsDiag Black Box Tech Support FREE! Live /7