Cooper Bussmann BU-905U-L Radio Transmission Distances, RG58 RG213 Cellfoil, Australia/NZ 20+ km

Page 10

Cooper Bussmann BU-905U-L Wireless I/O Installation Manual

For example, an BU-SG900-6 antenna with a BU-CC20-SMA cable kit has a net gain of 2dB (i.e., +8 dB – 6 dB) at 900 MHz.

The BU-905U-L-R module has no limitation on antenna gain, as this module does not incorporate a radio transmitter.

The following table details the gains of some typical antennas:

Antenna

Gain (dBi)

Dipole with integral 3m cable

0

Dipole without cable

2

5dBi Collinear (3dBd)

5

8dBi Collinear (6dBd)

8

3 element Yagi

5

6 element Yagi

10

The following table details losses for typical cables:

Cable

Loss (dB per 10m) at 900 MHz

RG58

-5

RG213

-2.5

Cellfoil

-3

Radio Transmission Distances

The unit will operate reliably over large distances depending on the:

Antenna type;

Antenna location;

Amount of radio interference; and

Radio path obstructions (e.g., hills or trees). Typical reliable distances are:

Area

Distance

Additional information

USA/Canada

20+ miles

6dB net gain antenna configuration permitted (4W Equivalent RF power permitted).

Australia/NZ

20+ km

Unity gain antenna configuration (1W Equivalent RF power permitted).

To achieve these distance, you must elevate at least one site on a hill or transmission tower.

Modules will operate reliably with some radio path obstruction; however obstructions also reduce the reliable distance.

Note: You must test all obstructed paths to check the reliability of the path.

You can achieve maximum transmission distances if the radio path has “line of sight.” For example, raising antennas above intermediate obstructions including hills, trees, etc. Obstructions reduce the range; however they may not prevent a reliable path.

The closer the obstruction is to the antenna, the greater the blocking effect. For example, a group of trees around the antenna is a larger obstruction than a group of trees further away from the antenna. You can achieve longer distances by mounting one antenna on top of a hill.

Note; Due to the earth’s curvature, you must elevate antennas higher than the ground level between the antennas for longer paths (greater than 3 miles / 5 km).

The unit can tolerate larger amounts of obstructions for shorter distances. For very short distances, you can also mount the antennas inside buildings.

If two BU-905U-L modules cannot communicate reliably, you can use a third 905U module as a “repeater” to receive and re-transmit messages. This module may also have input/output (I/O) signals connected to it and form part of the I/O network.

10

www.cooperbussmann.com/BussmannWirelessResources

3A1580Rev1.6

Image 10
Contents Cooper Bussmann BU-905U-L Wireless I/O Installation Manual Contents Cooper Bussmann Application EngineeringIndustry Canada BU-905U-L Wireless I/O Module Safety InformationFCC Notice when used in USA 905U Wireless I/O Module Safety Information FCC NoticeAbout This Document Installing Your UnitSpecifications Know technical information about your unit Section Read this section if you want toUnit Components and Connections Transmitter UnitIndicates Receiver Unit LEDs with Rssi Push PG LED on Configuration Cable Connected Output LED onSignal Strength Button PressedInstalling the Antenna Supported AntennasArea Distance Additional information USA/Canada 20+ miles Radio Transmission DistancesRG58 RG213 Cellfoil Australia/NZ 20+ kmOmni-directional Antennas Installing and Earthing AntennasCollinear Antennas 3A1580Rev1.6 Vertical polarization for the stations Yagi Directional AntennasHorizontal polarization for the stations With a common stationInstalling the Power Supply Digital Inputs Inputs and OutputsVoltage free contact Active 0-5v signal device Connection MethodImportant Safety Information Relay OutputsAnalog Input Status OutputsStatus Output Wire Transducer Current Source Output Thermocouple Input Current sink outputMinimum on time Pulse InputPassive transistor Active pulse device Analog Output Installing the Unit Installing and Configuring the UnitOther Signals Configuring Your UnitsSignals Sent Over Radio SendsTesting Your Units Transmitter Unit Unit SpecificationsReceiver Unit RS232 Serial Cable Signal Name Normal ColorAncillary Hardware Reference Information Parity No parityConnections ConfigurationIndex ReceiverCooper Bussmann BU-905U-L Wireless I/O Installation Manual Customer Assistance

BU-905U-L specifications

The Cooper Bussmann BU-905U-L is a critical component known for its reliable performance in various electrical applications. This fuse is designed to protect circuits from overloads and short circuits, ensuring the safety and integrity of electrical systems in residential, commercial, and industrial settings.

One of the main features of the BU-905U-L is its high breaking capacity, which allows it to effectively interrupt excessive current flow without damaging connected devices. This feature makes it suitable for use in demanding environments where reliable protection is crucial. The fuse is built to handle transient events, making it ideal for applications subject to short bursts of high current.

The fuse utilizes advanced materials and technologies to enhance its durability and efficiency. Its construction includes a robust, non-combustible housing that offers excellent thermal resistance and mechanical strength. This ensures the fuse can withstand harsh operating conditions while maintaining its protective capabilities. The BU-905U-L is also designed for quick and easy replacement, minimizing downtime during maintenance.

Another significant characteristic of the BU-905U-L is its thoughtful design for ease of installation. It features a standard size that is compatible with various fuse holders, allowing for a seamless integration into existing systems. Additionally, the fuse is marked with clear ratings, enabling users to quickly identify its specifications for proper selection and installation.

In terms of electrical ratings, the BU-905U-L is designed to handle a specific voltage and current, which makes it suitable for a diverse range of applications, including motor protection, lighting circuits, and power distribution systems. These fuses come with various current ratings, offering flexibility for different load requirements.

Moreover, built on a commitment to safety and quality, Cooper Bussmann ensures that the BU-905U-L meets stringent industry standards and certifications. This not only guarantees the reliability of the product but also provides peace of mind to users knowing that their electrical systems are well protected.

In summary, the Cooper Bussmann BU-905U-L fuse combines high performance, advanced material technology, and user-friendly characteristics, making it an invaluable component in any electrical system. Whether for industrial machinery or everyday electrical circuits, this fuse provides essential protection, ensuring safety and reliability in energy management.