Star Micronics LC24-10 user manual Self Declaration

Page 2

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates and uses radio frequency energy and if not installed and used properly,

that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio

and television reception It has been type tested and found to comply with the limits for a Class

B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules,

which are designed to provide reasonable protection against such interference in a residential

installation. However, there is no guarantee that interference will not occur in a particular in- stallation. If this equipment does cause interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient the receiving antenna

•Relocate the computer or printer with respect to the receiver

•Move the computer or printer away from the receiver

• Plug the

computer

or printer into a different outlet so that it and the receiver are on

-

different

branch

circuits.

 

If necessary, the user should consult the dealer or an experienced redio/television technician

for additional suggestions. The user may find the following booklet, prepared by the Federal

Communications Commission helpful: “How to Identify and Resolve Radio-TV Interference

Problems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

The above statement applies only to printers marketed in the U.S.A.

Self Declaration

Radio interference regarding this equipment has been eliminated according to Vfg 1046/1984

announced by the DBP. DBP has been informed of the introduction of this special equipment and has been granted the right to examine the whole series.

It is the user’s responsibility to see that his own assembled system is in accordance with the

technical regulations under Vfg 1046/1984.

To conform to FTZ-regulations it is necessary to make all connections to the printer with shielded cable.

The equipment may only be opened by qualified service representatives.

The above statement applies only to printers marketed in West Germany.

Trademark Acknowledgements

LCZ4-10, NE15, NB24-10, NB24-15: Star Micronics Co., Ltd.

IBM PC, Proprinter X24, Proprinter II, PC-DOS: International Business Machines Corp.

Microsoft BASIC, MS-DOS: Microsoft Corporation

LQ-800, LQ-1000, LQ-1500: Seiko Epson Corp.

NOTICE

•All rights reserved. Reproduction of any part of this manual in any form whatsoever

without STAR’s express permission is forbidden.

0 The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual at the time of press. However, should any errors be detected, STAR would greatly appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in this manual.

0 Copyright 1988 Star Micronics Co., Ltd.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents LC24-10 Self Declaration HOW to USE this Manual Features of the Printer Quad-sized Tableofcontents Commercial Software Index Unpacking and Inspection Check fhe carton contentsLocating the Printer Page Remove the top cover Setting UPMount the platen knob Lnstaii the ribbon cartridge Removing the top coverReplace the top cover Lnsfall the optional IC cardMount the paper guide Connect the printer’s power cordConnect the printer to the computer Loading Single SheetsSemiautomatic loading Mounting the paper guide for single sheetsManual loading Loading and Parking Fanfold Forms Opening the rear coverClamp Lever Paper parking Figure I-12. Mounting the paper guide tor tantola formsTest Printing Short se/f testPaper unparking Long self test Interface testAdjusting the Printing GAP DIP Switch SettingsInternational character set Print style and pitch selection Page Page OFF 1 OFF Power indicator Switches and IndicatorsOn Line switch Paper feed switchQuiet Mode switch Sty/e/Pitch switchShort test pattern On Line switch POWER-UP FunctionsLprint CHR$I Next Return Switch Combination Functions Switch combination functions of control panelPage Page Memo Installing Your Software Printer menuPrinter command options Type stylesLnitializa tion sequence Setting the DIP SwitchesUsing Your Software AlignmentOther printer commands Type style and pitch selectionCan help you to use italic print Memo Using the Printer with DOS and Basic HARD-COPYING the Screen MS-DOS and PC-DOSProgramming the Printer with DOS Commands Name of list device PRNNew file Programming the Printer with Basic Acopy LQELITE.DAT PRN Aprint README.DOCLprint Lprint the Spacings are Changed Next ROW How the program works IBM Lprint E$=CHR$oc!iR$60cHR$60 Lprint IQ= CHR$0CHR$60CHR$60 Cleaning the Printer Replacing the RibbonReplacing the Print Head Page Replacing the Battery in the RAM Card Troubleshooting If the printer doesn’t printIf the printed characters don’t match the characters on If you have problems with graphicsIf you have problems with download characters ScreenAppendix Dot Matrix Size Character SetsOnly1 Environmental Requirements Electrical SpecificationsFnterface Signals OptionPaper Memo Font Control Commands Select draft quality charactersSelect ornament character Select LQ charactersSelect LQ type style Select italic charactersSelect Upright Characters Cancel EmphasizedCancel double-strike printing Emphasized PrintingStart Overlining Cancel superscript or subscriptStop Underlining Stop overliningCharacter SET Commands SetSelect Ash Zero Enable printing of a// character codesEnable printing of a// character codes on next character SelectHigh-speed elite pitch Pica pitchElite pitch High-density elite pitchPrinting Cancel condensed printingCancel expanded printing Expanded printingCaucel one-line expanded printing Print Double-height Characters Increase character SpacingSelect double or quadruple size Return To normal HeightSelect Character WidthSet line spacing to l/8 inch CommandsSelect character type and print pitch Set line spacing to 7160 or 7172 inchSet line spacing to n/780 or n/276 inch Set line spacing to l/6 inchSet base unit for line spacing Set line spacing to n/360 inchSelect Forward Feed Select Reverse FeedFeed paper n lines Perform one n/180-inch or n/276-inch line feedPerform one nl7804nch reverse line feed Set top of page at current positionSet top margin Cancel top and bottom marginsSet page length to n inches Set bottom MarginSet vertical tab stops Disable paper-out detectorEnable paper-out detector Set vertical tab stops every n linesVertical tab Horizontal Position CommandsSelect Vertical Tab Channel Set left marginSet left and right margins 27 88 nlRight justify Left justifyCenter text Full JustifySet horizontal tab stops Horizontal tabAbsolute horizontal tab in inches Relative horizontal TabRelative horizontal tab in inches Absolute horizontal tab in columnsSing/e-density Graphics Print 8-MPrint b-bit double-density graphics Select graphics mode Print 24bit hex-density graphicsDensity Select graphics ModeDownload Character Commands Copy standard characters from ROM into RAMDefine Download Characters Select download character setAccept MSB as is Select ROM characterSet MSB to Delete last character sentRepeat data Cancel LastCancel Quiet Print Quiet PrintSet printer on-line PrintSet printer off-line Stop printingOne-line unidirectional printing PrintingUnidirectional printing Manual feedSet print start position on ASF Reset printerEject paper From ASF Memo Appenciix Download Normal characterCharacter width Figure C-2. Telephone symbol, super/subscript Super/subscript character1120 1600 2440 Else CS$=STRINGQ2,2 Output Diskette AppendixD Standardcharacterset Page IBM Character SET #2 Page IBM Character SET #l Additional Character SET International Character Sets Index DEI 107 Command Summary ESC EfjC O O O ESC ‘I=‘ ESC pCO 111

LC24-10 specifications

The Star Micronics LC24-10 is a robust and high-performance dot matrix printer that caters primarily to the needs of businesses requiring reliable and efficient printing solutions. Known for its durability and versatility, the LC24-10 is ideal for environments such as retail, manufacturing, and warehousing, where multi-part forms and continuous printing are crucial.

One of the standout features of the LC24-10 is its ability to handle various paper types and formats. It can print on single-sheet paper, multi-part forms, and labels, making it a versatile choice for myriad applications. The printer supports both standard and custom paper sizes, ensuring it meets the diverse needs of end-users.

In terms of technology, the LC24-10 utilizes a 24-pin print head which offers high-speed and high-quality printing. This print head technology enables the printer to produce sharp and clear characters, even when printing on thick or multi-part media. The printer can reach print speeds of up to 550 characters per second, significantly improving productivity in fast-paced environments.

The LC24-10 is designed with user-friendliness in mind. It features a simple control panel that allows for easy configuration and status monitoring. Additionally, the printer supports a variety of connectivity options, including parallel, serial, and USB interfaces, making it compatible with a wide range of systems and devices. This flexibility allows businesses to integrate the printer seamlessly into their existing operations.

Durability is another key characteristic of the LC24-10. Its rugged design ensures that it can withstand the rigors of busy working environments, with a mean time between failure (MTBF) rated at over 10,000 hours. This reliability translates to less downtime and lower overall maintenance costs for businesses.

Furthermore, the LC24-10 is equipped with advanced features such as a slip-feed mechanism that allows for easy loading of various media types without jamming. It also boasts multiple character sets and emulations, enabling it to cater to different printing needs without compromising on quality.

In summary, the Star Micronics LC24-10 stands out in the world of dot matrix printers due to its robust design, versatility in handling various media, high-speed performance, and user-friendly features. These characteristics make it an excellent choice for businesses that require heavy-duty printing capabilities.
Top Page Image Contents