IBM RS/6000 7043 43P Series, SN32-9080-01 manual Replacement

Page 10

Replacement

1.If you are replacing a fansink 09P1125, install the new component by hooking the side opposite the finger tab and then pushing the finger tab side down until it locks into position.

OR

If you are replacing a fansink 09P1126, first remove the paper pull tab to expose the thermal grease underneath. Install the new fansink by hooking the side opposite the finger tab and then pushing the finger tab side down until it locks into position.

2.Plug the new fansink into the system board connector of the old fansink.

3.Reinstall the disk drive bracket assembly (and any PCI Adapter Cards that were removed from slot 5).

4.Reinstall the top cover.

5.Power on the system and run diagnostics.

Removing and Replacing the 7043±150 System Board Fansink

Removal

1.Inform the customer that the system must be powered off for approximately one hour for the fan to be replaced.

2.To power off the system, refer to the ²Removal and Replacement Procedures² chapter in the RS/6000 7043±43P Series Service Guide. Power off the system as described in ²Cover Removal² and continue to unlock and remove the cover.

3.Determine the system board assembly part number by noting the white barcode label attached to the card.

Locate the assembly part number in the leftmost alphanumeric block of characters, following the first three characters, which are always 11S. In the following example, the assembly part number is 41L5812.

The FRU part number is in the center alphanumeric block of characters, following the first three characters which are always FRU. In the following example, the FRU part number is 41L5912.

11S41L5812YL1109140246 FRU41L5912 905

After you have identified both the system board assembly part number and the FRU part number, see the table inªDetermining the Fansink Assembly Number to be Replacedº on page 1 to determine the appropriate fan to be replaced.

4.To remove the disk drive bracket, refer to the ²Removing Internal Drive² section of the RS/6000 7043±43P Series Service Guide.

Note: If a hard file is attached to the disk drive bracket, unplug the hard file before removing the bracket assembly.

4Supplement to the Service Guide and User's Guide

Page 9 Page 11
Image 10
Page 9 Page 11
Contents IBM Second Edition December Contents Iv Supplement to the Service Guide and Users Guide Online Publications Related Publications About This BookISO TrademarksVi Supplement to the Service Guide and Users Guide Determining the Fansink Assembly Number to be Replaced Identifying the Fansink Number11S41L5812YL1109140246 FRU41L5912 Fansink Location Replacement ±140 and 7043±150 Fansink Removal and Replacement Procedures Replacement ±150 System Features Front-Panel Display Security FeaturesKeyboard and Mouse Input/Output PortsSetting the Scsi Security Jumpers System Board Locations for Model ±150 System Features System Board, Cables, and Accessories Index FRU Number Units Per Assy Description Supplement to the Service Guide and Users Guide Appendix. Notices Supplement to the Service Guide and Users Guide Readers Comments Ð Wed Like to Hear From You How satisfied are you that the information in this book isBusiness Reply Mail Page Ibmr

SN32-9080-01, RS/6000 7043 43P Series specifications

The IBM SN32-9080-01, known as part of the RS/6000 7043 43P Series, is a robust workstation designed to meet the demanding requirements of enterprise environments. This system incorporates advanced architectural features that cater to a wide array of applications, including scientific computations, engineering simulations, and complex data analysis processes.

At the heart of the SN32-9080-01 is its powerful architecture based on the PowerPC RISC (Reduced Instruction Set Computing) technology, which allows for efficient processing capabilities and optimized performance. This workstation is equipped with a scalable multi-processor design that supports multiple PowerPC processors, significantly improving processing speeds and multitasking capabilities.

The SN32-9080-01 offers substantial memory options, supporting up to 1 GB of RAM, which is critical for handling large datasets and running memory-intensive applications. This large memory footprint enhances the ability to perform parallel processing and facilitates quick data access, vital for performance-intensive tasks.

This model features an expansive input/output architecture that allows for a wide range of peripherals and expansion options. The system supports various storage options, including SCSI, which enhances data transfer rates and connectivity to external storage devices. Coupled with a high-performance graphics subsystem, it provides superior visual outputs ideal for graphic design and CAD applications.

Moreover, this workstation operates on the AIX operating system, known for its stability and scalability, which is crucial for enterprise applications. AIX supports various programming languages and development tools, making it a preferred choice for developers working in a UNIX-based environment.

The IBM SN32-9080-01 is designed with robust security features, ensuring data integrity and protection against unauthorized access. Its network capabilities are further enhanced by built-in support for various protocols, enabling seamless integration within existing network infrastructures.

Overall, the IBM SN32-9080-01 within the RS/6000 7043 43P Series is a versatile and high-performing workstation that remains relevant in scenarios demanding reliability and efficiency. Its architecture, scalability, and extensive feature set position it as an ideal choice for businesses aiming to leverage powerful computing capabilities for their operations.
Top Page Image Contents