Cisco Systems 3750 manual Configure, Related Products, Network Diagram

Page 4

Generating and distribution of the Distributed Cisco Express Forwarding (dCEF) database to the different stack members

The MAC address of the master is used as source MAC of routed packets

Packets that need process switching are handled by CPU of the master

The stack members perform the following tasks:

They act as routing standby switches which can take over when the stack master fails

Programming of the routes in the dCEF database in hardware

When the master fails, the stack members will (apart from a momentarily interruption) continue to forward the packets in hardware while no protocols are active.

After a new master has been selected following a master failure, the newly elected master will start sending gratuitous ARPs with its own MAC address in order to update the devices in the network with the new MAC address that will be used to rewrite the routed packets.

For more information regarding 3750 switch stack behavior and configuration, refer to the Managing Switch Stacks documentation.

Related Products

This configuration can also be used with the following hardware and software versions.

Any Catalyst 3750 switch running EMI software or SMI version 12.1(14)EA1 and later.

Any Catalyst 2900XL/3500XL/2950/3550 or Catalyst OS switches for access layer switch.

Configure

In this section, you are presented with the information to configure the features described in this document.

Note: To find additional information on the commands used in this document, use the Command Lookup Tool ( registered customers only) .

Network Diagram

This document uses the network setup shown in the diagram below.

Cisco − Configuring Inter−VLAN Routing with Catalyst 3750 Series Switches in a Stacked Configuration

Image 4
Contents Table of Contents Introduction Before You BeginDocument ID ConventionsBackground Theory Components UsedIP Routing on a Stack of 3750s Network Diagram ConfigureRelated Products Practical Tips Configurations Switchport trunk encapsulation dot1q Switchport access vlanSwitchport mode access No switchportIp address 10.1.2.1 Ip address 10.1.3.1Ip address 10.1.10.1 Ip route 0.0.0.0 0.0.0.0Cat2950#show running−config Switchport access vlan 3 switchport mode accessIp default−gateway Ip address 10.1.10.2Set vtp mode client Set ip route 0.0.0.0/0.0.0.0 10.1.10.1 #set boot commandSet vtp domain cisco Set interface sc0 10 10.1.10.3/255.255.255.0Verify ∙ show vtp status∙ show interfaces trunk ∙ show ip route∙ show vtp domain Troubleshooting Procedure TroubleshootRelated Information ∙ show trunkUpdated Mar 10 Document ID
Related manuals
Manual 176 pages 60.04 Kb

3750 specifications

The Cisco Systems 3750 series is a family of enterprise-class stackable switches that were designed to provide high-performance networking solutions for organizations requiring robust management features, security, and scalability. Known for their reliability and advanced capabilities, the 3750 series is particularly aimed at accommodating the demands of LAN environments in organizations ranging from small businesses to large enterprises.

One of the defining features of the Cisco 3750 series is its StackWise technology. This innovative feature enables the stacking of up to nine switches together, allowing them to function as a single logical unit. This results in simplified management, higher redundancy, and increased scalability. The StackWise technology allows for seamless failover and enhanced bandwidth between the stacked switches.

In terms of performance, the 3750 series supports Layer 2 and Layer 3 switching, offering routing capabilities to handle both traditional and modern network demands. It is equipped with advanced Quality of Service (QoS) features, ensuring that critical applications such as voice and video are prioritized for optimal performance.

The Cisco 3750 also features extensive security capabilities. It incorporates features such as IEEE 802.1X authentication, DHCP snooping, and dynamic ARP inspection to protect against unauthorized access and various network attacks. These enhancements help maintain data integrity and secure communications across the network.

Another noteworthy characteristic of the 3750 series is its support for Power over Ethernet (PoE). PoE allows for the delivery of power over Ethernet cables to connected devices, such as IP phones and wireless access points, facilitating simpler installations and reducing the need for additional power outlets.

The Cisco 3750 series also provides a comprehensive set of management tools. With features like Cisco's Embedded Event Manager (EEM) and extensive SNMP support, network administrators can efficiently monitor and manage network performance, troubleshoot issues, and maintain high availability.

Additionally, the series is compatible with Cisco's IOS software, which provides a rich set of features, including advanced routing protocols, multicast support, and extensive security options, further enhancing the functionality and versatility of the switches.

Overall, the Cisco Systems 3750 series stands out for its stackable design, high-performance features, security capabilities, and management tools, making it a popular choice for organizations looking for dependable and scalable networking solutions.