Cisco Systems manual Starting the Cisco Nexus 2000 Series Fabric Extender

Page 101

Chapter 3 Installing a Cisco Nexus 2000 Series Fabric Extender

Starting the Cisco Nexus 2000 Series Fabric Extender

Se n d d o c u m en t c o m m e n t s t o n e x u s5 k d o c s @ c is c o . c o m

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

Caution Grounding the chassis is required if you are using DC power supplies, even if the rack is already grounded. A grounding pad with two threaded M4 holes is provided on the chassis for attaching a grounding lug. The ground lug must be NRTL listed. In addition, the copper conductor (wires) must be used and the copper conductor must comply with the NEC code.

To attach the grounding lug and cable to the chassis, follow these steps:

Step 1 Use a wire-stripping tool to remove approximately 0.75 inches (19 mm) of the covering from the end of the grounding cable.

Step 2 Insert the stripped end of the grounding cable into the open end of the grounding lug. Step 3 Use the crimping tool to secure the grounding cable in the grounding lug.

Step 4 Remove the adhesive label from the grounding pad on the chassis.

Step 5 Place the grounding lug against the grounding pad so that there is solid metal-to-metal contact, and insert the two M4 screws with washers through the holes in the grounding lug and into the grounding pad.

Step 6 Ensure that the lug and cable do not interfere with other equipment.

Step 7 Prepare the other end of the grounding cable and connect it to an appropriate grounding point in your site to ensure adequate earth ground.

Starting the Cisco Nexus 2000 Series Fabric Extender

This section describes how to power up the device and verify the hardware operation.

Note Do not connect the Ethernet port to the LAN until the initial device configuration has been performed. For instructions on configuring the device, see the Cisco Nexus 2000 Series Fabric Extender Software Configuration Guide. For instructions on connecting to the console port, see the “Connecting to the 1-Gigabit Ethernet Port” section on page 4-2.

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

To power up the device and verify the hardware operation, follow these steps:

Step 1 Verify that the empty power supply bays have filler panels installed, the faceplates of all modules are flush with the front of the chassis, and the captive screws of the power supplies, fan tray, and all expansion modules are tight.

 

 

Cisco Nexus 2000 Series Hardware Installation Guide

 

 

 

 

 

 

OL-19013-05

 

 

3-15

 

 

 

 

 

Image 101
Contents Americas Headquarters Cisco Nexus 2000 Series Hardware Installation GuideCisco Nexus 2000 Series Fabric Extender N T E N T S Cisco Nexus 2232TM-10GE, Cisco NexusN2K-C2232TM-E-10GE1-21 Transceivers Supported by the Cisco Nexus 2232PP FEX Removing and Installing Power Supplies Power Cords Viii Chapter and Title Description AudienceOrganization Conventions InstallationBewaar Deze Instructies Xii Xiii Xiv Page Release Notes Configuration GuidesRelated Documentation Command References Installation and Upgrade GuidesError and System Messages Troubleshooting GuideObtaining Documentation and Submitting a Service Request Cisco Nexus 2248TP-E Front View of the Cisco Nexus 2248TP-E Chassis ChassisPart Number Power SuppliesPorts Power Supply Part Number DC Power Supply for the Cisco Nexus 2200 Platform Chassis Cisco Nexus 2000 Series Hardware Installation Guide Description Part Number Fan TraysFEXs Model Description Supported Transceivers and CablesCisco Nexus 2248TP 10 Front View of the Cisco Nexus 2248TP Chassis Ports Chassis Handle Fan Tray SFP Transceivers used with the Cisco Nexus 2248TP FEX Cisco Nexus 2248PQ Ports NXA-FAN-30CFM-B Supported SFP+ TransceiversQSFP+ Transceivers Cisco Nexus 2232TM-10GE, Cisco NexusN2K-C2232TM-E-10GE Power supply Fan tray Status top and ID bottom LEDs 19 Rear View of the Cisco Nexus 2232TM Chassis 14 Power Supplies for the Cisco Nexus 2232TM-10GE FEX 15 Fan Trays for the Cisco Nexus 2232TM-10GE FEX 16 SFP+ Transceivers for the Cisco Nexus 2232TM-10GE FEX 1Cisco Nexus 2224TP 23 Front of the Cisco Nexus 2224TP Chassis 24 Rear View of the Nexus 2224TP Chassis SFP+ Transceivers, SFP+ Copper Cables, Cisco Nexus 2148T 25identifies the front view of the Cisco Nexus 2148T FEX Features25 Front View of the Cisco Nexus 2148T FEX Group 1 Data ports 1 through Group 2 Uplink ports 1 through 29 Blank Power Supply Filler Panel Supported SFP Transceivers SFP-H10GB-CU7MA OL-19013-05 A P T E R Cisco Nexus 2248TP-E FEX Front View of the Cisco Nexus 2248TP-E Chassis Ports for the Cisco Nexus 2248TP-E FEX Power Supplies for the Cisco Nexus 2248TP-E FEXPage Black Stripe Used to Indicate Back-to-Front Airflow Fan Tray for the Cisco Nexus 2248TP-E FEX 239291 FET-10G 10 SFP+ Optical Transceivers and FETs Cisco Nexus 2248TP FEX 13 Front View of the Cisco Nexus 2248TP Chassis Ports for the Cisco Nexus 2248TP FEX Power Supplies for the Cisco Nexus 2248TP FEXFan Tray for the Cisco Nexus 2248TP FEX Cisco Nexus 2232TM FEX 16 Front View of the Cisco Nexus 2232TM Chassis Ports for the Cisco Nexus 2232TM FEX Power Supplies for the Cisco Nexus 2232TM FEXFan Tray for the Cisco Nexus 2232TM FEX OL-19013-05 Cisco Nexus 2232PP FEX 21 Front View of the Cisco Nexus 2232PP Chassis 22 Rear View of the Cisco Nexus 2232PP Chassis Ports for the Cisco Nexus 2232PP FEXFan Tray for the Cisco Nexus 2232PP FEX Power Supplies for the Cisco Nexus 2232PP FEXTransceivers Supported by the Cisco Nexus 2232PP FEX Cisco Nexus 2224TP FEX 24 Front View of the Cisco Nexus 2224TP Chassis Ports for the Cisco Nexus 2224TP FEX Power Supplies for the Cisco Nexus 2224TP FEXFan Tray for the Cisco Nexus 2224TP FEX OL-19013-05 Cisco Nexus 2000 Series Hardware Installation Guide Installing a Cisco Nexus 2000 Series Fabric Extender Airflow Considerations Preparing for InstallationInstallation Options Installation Guidelines Chassis WeightRequired Tools and Equipment Installing a Cisco Nexus 2000 Series Fabric Extender Quantity Part Description Insert the device into the rack as follows Sliding the Chassis Into the Rack Environment Level Grounding the SystemProper Grounding Guidelines Preventing Electrostatic Discharge Damage Cisco Nexus 2000 Series Hardware Installation Guide Attaching the ESD Wrist Strap to the System Ground Lug Screw Establishing the System Ground Location of System Ground on a Cisco Nexus 2000 Series FEX Grounding the ChassisStarting the Cisco Nexus 2000 Series Fabric Extender Cisco Nexus 2000 Series Hardware Installation Guide Removing and Installing Power Supplies Removing and Installing ComponentsInstalling an AC Power Supply Removing a DC Power Supply Removing a Fan Tray, Installing a Fan tray, Removing and Installing the Fan TrayRemoving a Fan Tray Removing the Cisco Nexus 2000 Series Fabric Extender Connecting a Cisco Nexus 2000 Series Fabric Extender Connecting to a 10-Gigabit Ethernet Port Connecting to the 1-Gigabit Ethernet PortRemoving and Installing SFP+ Transceivers Preparing for Network ConnectionsInstalling an SFP+ Transceiver Alternate Removal Method for Bale Clasp SFP+ Transceivers Removing and Installing Cables into SFP+ TransceiversRemoving a Cable from an SFP+ Transceiver Maintaining SFP+ Transceivers and Cables General Requirements for Cabinets and Racks Cabinet and Rack RequirementsRequirements Specific to Standard Open Racks Requirements Specific to Perforated CabinetsCable Management Guidelines OL-19013-05 Power Specifications Technical SpecificationsSeries Power SupplyCisco Nexus Appendix B Technical Specifications Cooling Environmental SpecificationsDescription Specification Physical SpecificationsSFP+ Optical Transceiver Specifications Transceiver SpecificationsSFP+ Copper Transceiver Specifications Airflow Optimization AccessoriesAccessories Airflow Extension Sleeve Airflow Vent Transceiver Cable LengthOL-19013-05 Power Cords Supported Power Cords and PlugsLength Description Feet Meters IllustrationCAB-9K10A-IT CAB-9K10A-AU CAB-9K10A-EU CAB-9K10A-IT CAB-N5K6A-NA CAB-9K12A-NA Power Cords Description Jumper Power CordFigure C-16 CAB-C13-C14-JMPR, Jumper Power Cord OL-19013-05 LEDs Status Chassis and Module LED DescriptionsComponent Status Description Power Supply StatusCondition OK LED Status Green Fail LED Status Amber ConditionEthernet Port LEDs Port LEDsEthernet and Fibre Channel LEDs Link State LED StateState OL-19013-05 Snmp Traps OverviewDevice Hardware Guidelines InstallationInitialization Device OperationContacting Customer Service OL-19013-05 Accessory Kit Details Accessory KitOL-19013-05 Site Preparation Checklist Site Preparation and Maintenance RecordsTask No Planning Activity Verified By Time Date Contact and Site Information Slot Module Type Module Serial Number Supervisor Chassis and Module InformationNumerics IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Related manuals
Manual 6 pages 36.39 Kb Manual 14 pages 34.83 Kb Manual 190 pages 15.11 Kb

2000 specifications

In the year 2000, Cisco Systems, a leading technology company, was at the forefront of networking and communication solutions. With a rich history of innovation, Cisco solidified its position as a global leader in providing advanced networking technologies, hardware, and software.

One of the most significant features of Cisco in 2000 was its comprehensive portfolio of routers and switches. The company was known for its powerful routers, which were essential for managing internet traffic efficiently. Cisco’s Catalyst series of switches provided high levels of performance and scalability, enabling companies to build robust local area networks (LANs). These devices supported Ethernet technologies and catered to the growing demands of businesses for faster and more reliable connectivity.

In the late 1990s and early 2000s, the internet was experiencing rapid growth, and Cisco capitalized on this surge by introducing technologies that facilitated internet protocol (IP) networking. Its focus on developing IP-based solutions allowed businesses to integrate voice, video, and data services seamlessly over a single network. This was a significant advancement known as convergence, fundamentally changing how organizations approached communication.

Another characteristic of Cisco in 2000 was its commitment to security. As businesses began to increase their reliance on the internet, the risks associated with cyber threats also grew. Cisco developed security solutions such as firewalls and intrusion detection systems to help protect networks from potential attacks. The introduction of the Cisco Secure Network Architecture laid the foundation for comprehensive network security strategies.

Cisco also emphasized research and development, consistently investing in new technologies and innovations. The company was a pioneer in developing optical networking solutions, which enabled faster data transmission over long distances. This was crucial for supporting the growing bandwidth demands of the era.

Furthermore, Cisco’s collaboration with various technology partners and its global presence allowed it to provide customers with tailored solutions to meet diverse needs across different industries. The introduction of certification programs, like the Cisco Certified Network Associate (CCNA), helped create a skilled workforce equipped to deploy and manage Cisco technologies effectively.

In summary, Cisco Systems in 2000 showcased a blend of powerful routing and switching capabilities, a commitment to internet security, and innovative solutions that paved the way for future networking technologies. Its focus on convergence and relentless drive for high-performance networking made it a vital player in the evolving landscape of technology during this period.