Cisco Systems 3700 Series manual PS1, PS2 Amber

Page 91

Appendix A Troubleshooting

Error Messages

Table A-5 System Error and Recovery Messages (continued)

LED Type

LED Color

Message

 

 

 

System

Amber

Error:

 

 

%PS-3-MULTFAIL: There is more than one failure with the Power System #; please

PS1, PS2,

Amber

resolve problems immediately.

 

LED on

 

Explanation:

power

 

The specified power supply (1 or 2) has experienced multiple failures. This is a critical

supply rear

 

 

condition that must be resolved immediately.

panel

 

 

Recovery:

 

 

 

 

1. Check the power supply LEDs to identify the faulty unit.

 

 

2. Power down the faulty power supply and circuit breaker (for a DC power supply).

 

 

3. Check that cables are seated properly and terminal blocks are wired correctly.

 

 

4. Power up the circuit breaker (for a DC power supply) and the power supply.

 

 

5. If the error condition persists, replace the power supply. See the instructions that ship with

 

 

the new power supply.)

 

 

When the error condition is resolved, the following informational message appears:

 

 

%PS-3-PSOK: Power System is now normal.

 

 

 

Error:

 

 

%FAN-3-FAN_FAILED: Fan # had a rotation error reported.

 

 

Explanation:

 

 

The specified fan is not rotating at the desired speed.

 

 

Recovery:

 

 

Replace the fan cage as described in the Installing Field-Replaceable Units in Cisco 3745

 

 

Routers hardware configuration note.

 

 

When the error condition is resolved, the following informational message appears:

 

 

%FAN-3-FAN_OK: Fan # had earlier reported a rotation error. It is ok now.

 

 

 

Error:

 

 

%OIR-6-REMCARD: Card removed from slot x, interfaces disabled.

 

 

Explanation:

 

 

The online insertion and removal (OIR) function detected the removal of a network module

 

 

processor from the specified chassis slot. The interfaces on that processor are administratively

 

 

shut down and removed. In addition, the routing table is flushed of any routes through the

 

 

removed interfaces.

 

 

For more information, see the online Cisco Network Modules Hardware Installation Guide.

 

 

This is an informational message that does not require any recovery procedure.

 

 

 

Cisco 3700 Series Routers Hardware Installation Guide

 

OL-2180-08

A-11

 

Image 91
Contents Corporate Headquarters Cisco 3700 Series Routers Hardware Installation GuideBook Title N T E N T S Site Environment Entering ROM Monitor Mode B-1 Cisco 3700 Series Routers Hardware Installation Guide Objectives PrefaceChapter Title Description AudienceOrganization ConventionsBewaar Deze Instructies Safety WarningsAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseGuarde Estas Instruções Aviso Instruções Importantes DE SegurançaGEM Disse Anvisninger Xiii Related Documentation Cisco Product Document Title Ordering Documentation Obtaining DocumentationDocumentation Feedback Cisco.comObtaining Technical Assistance Submitting a Service RequestCisco Technical Support Website Obtaining Additional Publications and Information Definitions of Service Request SeverityXix OL-2180-08 Cisco Hardware Features1shows the rear panel of the Cisco 3725 router 2shows the rear panel of the Cisco 3745 router Modules, Interface Cards, and MemoryMemory Description SpecificationCisco 3725 Interfaces Interface NumberingWAN and LAN Interface Numbering Gigabit Ethernet 2/0 Voice Interface NumberingCisco 3745 Interfaces Network-module-slot/voice-module-slot/voice-interface Internal -48 V Telephony Power Modules Power Supply OptionsPower Supply Option Cisco Cisco 3725 Router with Optional -48 V Power Module Installed System Specifications Regulatory Compliance Safety Recommendations Preparing to Install the RouterPreventing Electrostatic Discharge Damage Safety with ElectricityRouter Power Supply Input Power Input Voltage Power Supply ConsiderationsGeneral Site Requirements Site Environment Site ConfigurationEquipment Racks Task Verified by Date Installation ChecklistInspecting the Router Creating a Site LogPage Console Port Connections Console and Auxiliary Port ConsiderationsAuxiliary Port Connections Ethernet Connections Preparing to Connect to a NetworkSerial DTE or DCE Devices Configuring Serial ConnectionsToken Ring Connections Serial ConnectionsDistance Limitations Signaling Standards SupportedDevice Type Gender Typical Devices Distance EIA-530 Distance Rate bps Feet Meters Isdn BRI ConnectionsAsynchronous/Synchronous Serial Module Data Rates EIA/TIA-232Low-Capacitance Cable 56-K/Switched-56-kbps DSU/CSU ConnectionsOL-2180-07 Installing the Router Setting the Chassis on a Desktop Setting Up the ChassisRack-Mounting the Chassis LeftCisco 3745 Router-Brackets for 19-Inch Rack Attaching Brackets to the Cisco 3725 RouterRight wide bracket Right Attaching Brackets to the Cisco 3745 Router63387 Mounting the Router in a Rack11 Mounting the Chassis in a Rack Typical Installing the Chassis Ground ConnectionGround lug Cisco 3725 Router Ground ConnectionCisco 3745 Router Ground Connection Installing the Router Power Connections Power Connections15A, 120VAC 10A, 240VAC. Statement Connecting Routers to AC PowerConnecting Routers to a DC-Input Power Supply Wiring the DC-Input Power Supply in Cisco 3725 RoutersSource DC Input Wire Size Wire Terminal Lug Protection DC Power DC Input+ B 17 DC Wire Routing and Attachment for Cisco 127039 Wiring the DC-Input Power Supply in Cisco 3745 Routers Installed Power Supply DC Input Size Wire Size DC Input WireNegative polarity input 0V return Safety ground Connecting Routers to the Cisco Redundant Power System Connecting WAN, LAN, and Voice CablesPorts and Cabling Port or Connection Port type, color Cable Connection Procedures and PrecautionsConnecting to the Console Port Connecting to a Console Terminal or Modem24 Connecting a Console Terminal to a Cisco 3725 Router Specifications on Cisco.com Connecting to the Auxiliary Port28 Identifying a Rollover Cable Identifying a Rollover CableChecklist for Power Up Powering Up the RouterFront Panel Indicators Cisco 3745 LED Indicators Power-Up ProcedureYourname con0 is now available Press Return to get started Initial Configuration Using SDM Configuring the RouterInitial Configuration Using the Setup Command Facility Shown as examples only Configuration is displayed Initial Configuration Using the CLI Manual Configuration Press Return to bring up the Router prompt OL-2180-08 Troubleshooting Troubleshooting the Power and Cooling Systems Solving ProblemsTroubleshooting Modules, Cables, and Connections Environmental Reporting FeaturesACT LED SYS/RPS LED PWR LED Reading Front-Panel LEDsSYS/RPS LED Indicator State DescriptionSYS PS1 Reading Rear Panel LEDsPower ETM Error MessagesLED Type LED Color Message System Amber ErrorPS1, PS2 Amber Error LED on PS1, PS2 Amber Recovering a Lost Password Entering ROM Monitor Mode Using the ROM MonitorEnter ROM Monitor Mode by Using the reload Command ROM Monitor CommandsBoot Commands in the ROM Monitor ROM Monitor Command DescriptionsROM Monitor Syntax Conventions Cisco 3700 Series Routers Hardware Installation Guide Informational Commands in the ROM Monitor Debugging Commands in the ROM Monitor Other Useful ROM Monitor CommandsConfiguration Register Modifying the Configuration Register by Hexadecimal Entry Modifying the Configuration Register in Menu ModeDescription and Options of the xmodem Command Recovering Cisco IOS Software ImagesConsole Requirements Messages similar to the following appear Procedure for the xmodem CommandOL-2180-08 Bit Number Hexadecimal Meaning Configuration Register SettingsYour router is now in the normal operating mode Changing Configuration Register SettingsBoot Field Meaning Configuring the Boot FieldBit Address net host Data Rate Bit Enabling Booting from CompactFlash MemoryOL-2180-08 Symbols IN-2 IN-3 IN-4 IN-5 IN-6

3700 Series specifications

Cisco Systems 3700 Series routers are a pivotal part of Cisco's portfolio, designed for medium to large enterprises aiming to deliver secure and efficient networking capabilities. Introduced as a versatile solution, these routers provide a comprehensive blend of performance, scalability, and investment protection.

One of the standout features of the Cisco 3700 Series is its modular architecture, allowing organizations to customize their router according to specific needs. This modularity supports various modules for different functions, including voice, data, and video, making the 3700 Series an ideal choice for converged networking environments. Administrators can enhance functionality through an array of WAN and voice interface cards that adapt as the organization's needs evolve.

The 3700 Series is built on Cisco's IOS (Internetwork Operating System), ensuring robust and high-quality performance. It supports advanced routing protocols including EIGRP, OSPF, and BGP, facilitating efficient data transmission across diverse environments. This versatility helps organizations implement sophisticated multi-site connectivity and enables reliable performance in complex network scenarios.

Security is a paramount concern in modern networking, and the Cisco 3700 Series delivers with features such as integrated firewall services, VPN support, and intrusion detection capabilities. These security measures protect sensitive data and ensure secure communication between remote sites—critical in today’s cyber landscape.

Another key characteristic of the 3700 Series is its support for Quality of Service (QoS), which prioritizes time-sensitive traffic such as voice and video. By ensuring that critical applications receive the bandwidth they require, organizations can maintain the quality of service that their users expect.

Moreover, the Cisco 3700 Series is designed with redundancy in mind. Features like dual power supplies and hot-swappable fan trays enhance reliability and uptime, which are crucial for mission-critical applications.

Furthermore, energy efficiency is an increasingly important consideration in network design. The Cisco 3700 Series adheres to modern energy standards, helping reduce the overall carbon footprint while supporting high-performance capabilities.

In summary, the Cisco Systems 3700 Series routers stand out for their modularity, advanced routing capabilities, robust security features, and energy efficiency, making them an optimal choice for enterprises that not only need performance but also flexibility and reliability in their networking solutions. As businesses continue to evolve and adapt, the Cisco 3700 Series is a dependable partner in their connectivity journey, ensuring they can meet current demands while preparing for future challenges.