Cisco Systems WAP4410N manual Placement Options, Desktop Option, Wall-Mount Option

Page 18

4

Connecting the WAP4410N Access Point

This chapter describes how to place and connect the WAP4410N Access Point to your network.

Depending on your application, you might want to set up the device first before mounting it.

Placement Options

You can place the WAP4410N Access Point horizontally on its rubber feet, vertically in a stand, or mount it on the wall.

Desktop Option

For desktop mounting, place the access point horizontally on a surface so it sits on its four rubber feet.

Wall-Mount Option

To mount the WAP4410N Access Point on a wall, follow these steps.

STEP 1 Determine where you want to mount the WAP4410N Access Point and install two screws (not supplied) that are 2-15/16 inches apart (approximately 7.46 cm.).

STEP 2 With the back panel pointing up (if installing vertically), line up the WAP4410N Access Point so that the wall-mount crisscross slots on the bottom of the access point line up with the two screws.

WAP4410N Wireless-N Access Point with Power Over Internet

9

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Administration Guide Cisco Systems, Inc. All rights reserved OL-19774-01 Getting to Know the Wireless-N Access Point Contents About This DocumentIntroduction Planning Your Wireless Network Connecting the WAP4410N Access PointContents Setting Up the WAP4410N Wireless-N Access Point Configuring the WAP4410N Wireless-N Access PointContents Appendix a Troubleshooting and HelpAppendix B Wireless Security Audience OrganizationPreface Troubleshooting Press Enter Click Search Introduction Introduction Network Topology RoamingExample of a Simple Wireless Network Network LayoutExample of a Simple Wireless Network Getting to Know the Wireless-N Access Point Front PanelBack Panel Antennas and Positions Placement Options Desktop OptionWall-Mount Option Connecting the WAP4410N Access Point Stand OptionConnecting the WAP4410N Access Point to the Network Connecting the WAP4410N Access Point Connecting the WAP4410N Access Point Setting Up the WAP4410N Wireless-N Access Point Launching the Web-Based Configuration UtilitySetup WirelessNavigating the Utility AP Mode AdministrationStatus Setting Up the WAP4410N Wireless-N Access Point Configuring the WAP4410N Wireless-N Access Point Setting Up Your Access PointConfiguring Basic Setup Settings Configuring Device Setup Settings Configuring Network Setup SettingsClick Setup Basic Setup Configuring the WAP4410N Wireless-N Access Point Configuring Time Settings Click Setup TimeSelect Automatically Configuring Advanced Settings Wireless Click Setup AdvancedConfiguring Basic Settings Click Wireless Basic SettingsConfiguring the WAP4410N Wireless-N Access Point Configuring Security Click Wireless SecurityWEP Configuring WAP-Personal Security Configuring WAP2-Personal Security Configuring WPA2-Personal Mixed Security Configuring WPA-Enterprise Security Configuring WPA2-Enterprise Security Configuring the WAP4410N Wireless-N Access Point Configuring WPA2-Enterprise Mixed Security Configuring the WAP4410N Wireless-N Access Point Configuring Radius Security Configuring WEP Security Configuring Connection Control Click Wireless Connection Control Click Disabled Disabling Connection ControlClick Wireless Connection Control Enabling Local Connection ControlEnabling Radius Connection Control Configuring Wi-Fi Protected Setup Click Wireless Wi-Fi Protected SetupConfiguring Vlan & QoS Click Wireless Vlan & QoS Vlan Tag over WDS-SelectEnabled or Disabled as requiredClick Wireless Advanced Configuring the WAP4410N Wireless-N Access Point Click Save Configuring the AP Mode Click AP Mode AP Mode Administration Configuring Administration Settings Click Administration ManagementLocal AP Password Identification Configuring Administration Log Click Administration LogEmail Alert Configuring the WAP4410N Wireless-N Access Point Diagnosing Access Point Problems Click Administration DiagnosticsRestoring Factory Default Settings Restoring Factory DefaultsUpgrading the Firmware Rebooting the Access Point Click Administration Firmware UpgradeManaging the Access Point’s Configuration Click Administration RebootConfiguring Status Settings Click Administration Config ManagementChecking Local Network Status Click Status Local Network InformationLocal Network Checking the Wireless Status Click Status WirelessChecking System Performance Configuring the WAP4410N Wireless-N Access Point Troubleshooting and Help Frequently Asked QuestionsTroubleshooting and Help WEB/SSL Sntp PING6 Troubleshooting and Help Troubleshooting and Help Troubleshooting and Help Windows Help TCP/IPShared Resources Network Neighborhood/My Network PlacesWireless Security Security PrecautionsChange the administrator’s password regularly Protecting Your NetworkProtecting your Ssid WPA/WPA2 Personal MAC AddressesWEP Encryption WPA /WPA2 EnterpriseUpgrading Firmware Upgrading Firmware Specifications Specifications WAP4410N Specifications Spec/Modulation Where to Go From Here Product ResourcesRelated Documentation

WAP4410N specifications

The Cisco Systems WAP4410N is a robust Wireless-N access point designed to enhance connectivity in small to medium-sized business environments. It provides seamless, high-performance wireless connections while maintaining security and managing features that cater to the needs of modern enterprises.

One of the standout features of the WAP4410N is its Wireless-N technology, which offers improved range and speed compared to previous wireless standards. With dual-band support of both 2.4 GHz and 5 GHz frequencies, the device delivers enhanced performance by allowing users to connect to the less congested 5 GHz band for data-intensive applications. This capability significantly reduces interference from other devices, ensuring a stable and reliable connection.

The WAP4410N comes equipped with advanced security protocols, including WPA2, WPA, and WEP encryption, which play a crucial role in safeguarding sensitive data transmitted over the network. Additionally, it supports features such as MAC address filtering and VLANs, allowing administrators to create secure, segmented networks tailored to their specific needs.

For ease of management, the WAP4410N includes a user-friendly web-based interface, enabling quick configuration and monitoring of network settings. The device also supports Power over Ethernet (PoE), simplifying installation by eliminating the need for external power outlets.

The Cisco WAP4410N offers support for multiple SSIDs, allowing businesses to create distinct access profiles for guests and employees, thereby enhancing network security and management. Quality of Service (QoS) capabilities ensure that bandwidth is prioritized for critical applications, accommodating voice over IP (VoIP) and video streaming with minimal interruptions.

With a sleek, compact design and versatile mounting options, the WAP4410N can be easily installed in various environments, providing unobtrusive network coverage that is both effective and aesthetically pleasing.

Overall, the Cisco Systems WAP4410N stands out as a reliable and feature-rich access point that meets the demands of contemporary wireless networking, making it a valuable addition to any small or medium-sized business looking to improve its connectivity infrastructure.
Top Page Image Contents