Cabletron Systems Installing 6C105 Interface Modules, Engages the backplane connectors

Page 29

Setting Up the 6C105

3.2.6Installing 6C105 Interface Modules

The 6C105 Interface Modules can be installed in any of the 5 slots that are available. To install a module, proceed as follows:

1.Remove the blank panel covering the slot in which the Interface Module will be installed. All other slots must remain covered to ensure proper airflow and cooling. (Save the blank plate in the event you need to remove the module.)

2.Carefully remove the module from the shipping box. (Save the box and packing materials in the event the module must be reshipped.)

3.Locate the ESD wrist strap shipped with the 6C105. Attach the ESD wrist strap to your wrist and plug the cable from the ESD wrist strap into the ESD grounding receptacle at the upper right corner of the 6C105.

4.Remove the module from the plastic bag. (Save the bag in the event the module must be reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD).

5.Examine the module for damage. If any damage exists, DO NOT install the module. Immediately contact the Cabletron Systems Global Call Center.

To prevent damaging the backplane connectors in the following

!step, take care that the module slides in straight and properly

CAUTION

engages the backplane connectors.

 

NOTE

In the following step ensure that the top plastic locking tab lines up with the desired slot number located on the front panel of the chassis. Refer to Figure 3-5.

6.Locate the slot guides that line up with the number of the slot in which the module will be installed. Install the Interface Module in the chassis by aligning the module circuit card between the upper and lower metal rail guides of the desired slot, sliding it into the chassis, and locking down the top and bottom plastic locking tabs, as shown in Figure 3-5. Take care that the Interface Module slides in straight and properly engages the backplane connectors.

6C105 Overview and Setup Guide

3-9

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 6C105 SmartSwitch 6000 Overview and Setup Guide Page 6C105 Overview and Setup Guide DOC Notice Cabletron Software Program License Declaration of Conformity Contents Contents 6C105 Overview and Setup Guide Structure of this Guide Using this GuideDocument Conventions Using the 6C105 Manual SETYour email address Getting HelpOverview 6C105 Chassis with Redundant Power SuppliesFeatures Auto-Ranging Power Supplies Site Guidelines Chapter Installation Requirements SpecificationsOperating Specifications Configuration GuidelinesPhysical Specifications LEDs Power Supply RequirementsPower Supply LEDs LEDs Fan Tray LED States and Their Definitions Fan Tray LEDUnpacking the 6C105 Chapter 6C105 SetupInstallation Order Setting UP the 6C105To install the cable management bar, proceed as follows Installing the Cable Management Bar6C105 can be mounted in a standard 19-inch equipment rack Rack Mounting the 6C105ESD Grounding Receptacle Attaching the Electrostatic Discharge Wrist StrapInstalling a Power Supply Module Setting Up the 6C105 Installing the Power Supply Modules Engages the backplane connectors Installing 6C105 Interface ModulesInstalling a Module Powering UP a 6C105 with DC Power Supplies Powering UP a 6C105 with AC Power SuppliesDC Power Supply Requirement for Each Supply 48 or 60 Vdc Power Source Connecting a 6C205-2 to a 48/60 VDC Power SourceRemoving the Fan Tray Removing and Reinstalling the FAN TrayRemoving the Fan Tray Reinstalling the Fan Tray6C105 Setup Reinstalling the Fan Tray 6C105 Setup 6C105 Overview and Setup Guide

6C105 specifications

Cabletron Systems, a prominent name in the networking equipment industry during the 1990s and early 2000s, introduced various innovative products aimed at enhancing network performance and reliability. One such product was the Cabletron Systems 6C105, a modular hub designed to meet the growing demands of enterprise-level networking.

The Cabletron 6C105 is primarily known for its high-density architecture, accommodating up to 48 connections, which allows for scalability within networking environments. This feature makes it particularly appealing for businesses anticipating growth or those that require extensive network connections. The 6C105 is ideal for environments that require a robust foundation for multiple devices and users without compromising performance.

One of the standout features of the 6C105 is its support for various network protocols, including Ethernet and Token Ring, making it versatile in terms of infrastructure compatibility. The device effectively supports both 10Base-T and 100Base-TX standards, enabling smooth data transmission at speeds of up to 100 Mbps. This adaptability ensures that organizations can integrate the hub regardless of their existing architecture.

The Cabletron 6C105 also showcases advanced management capabilities through the inclusion of SNMP (Simple Network Management Protocol). This management tool allows network administrators to monitor performance, troubleshoot issues, and manage the network efficiently. The SNMP compatibility is particularly vital for organizations that require comprehensive oversight for performance optimization and security management.

In terms of physical characteristics, the 6C105 features a compact, rack-mountable design, supporting efficient use of space in server rooms or data centers. Its modular design allows easy upgrades and maintenance, as network managers can add or replace components with minimal downtime.

The Cabletron Systems 6C105 exemplifies the technological foresight of its era, offering a solution that balances performance, flexibility, and manageability. Its longevity in the field and ability to adapt to evolving technologies speak volumes about its design integrity and utility. As organizations continue to seek reliable networking solutions, the legacy of the 6C105 remains a cornerstone in understanding the evolution of networking hardware.
Top Page Image Contents