Extron electronic DVS 510 setup guide Rear Panel Features and Connections, Installation Steps

DVS 510 Series • Setup Guide

The Extron DVS 510 Series scalers are 10-input, multi-format presentation switching scalers that accept and scale DVI, RGB, YUVp/HDTV, YUVi, S-video, and composite video signals to a common high-resolution output rate. Two models are available: the standard DVS 510, which has fixed and variable line level audio outputs, and the DVS 510 SA, which adds an integrated stereo amplifier. Control options include front panel buttons and knobs, Ethernet, RS-232 or RS-422, web pages, and infrared (IR). This guide provides instructions for an experienced installer to install and connect the DVS 510 scalers.

NOTE: For full installation, configuration, and operation details, see the DVS 510 Series User Guide, available at

www.extron.com.

Rear Panel Features and Connections

1		2
		1
	V
	I	VID
	D
	E
	O
100-240V 50-60 Hz	I
2A MAX	N
	P
	U
	T	VID

2

3

4

5

6

7

8

9

AMPLIFIED

A

3

5

U

L

R

D

RGB/R-Y, Y, B-Y

V

A

RGB/R-Y, Y, B-Y

1

3

5

7

9

I

VARIABLE

YC

I

U

O

D

D

E

I

O

O

O L

R

L

R

L

R

L

R

L

R

L

R

U

O

DVI-D

I

T

P

U

N

2

4

6

8

10

FIXED

U

T

P

T

P

U

YC

RGB/R-Y, Y, B-Y

DVI-I

DVI-I

U

RGB/R-Y, Y, B-Y

T

L

R

L

R

L

R

L

R

L

R

T

L

R

4

6

7/8

9/10

RS232

LAN

RESET

15

14

13

10

11

12

A AC power connector	H
B Video inputs 1 and 2: Composite video	I
C Video inputs 3 and 4: S-video	J
D Video inputs 5 and 6: RGB or YUV component	K
E Video inputs 7/8 and 9/10: RGB or YUV (7 and 9) and	L
DVI (8 and 10)	M
F Buffered RGB/YUV output connectors	N
G DVI-I output connector (digital output only)	O

Audio input connectors

Amplified audio output connector (DVS 510 SA only) Variable audio output connector

Fixed audio output connector Reset LED

Reset button LAN connector

RS-232/RS-422 connector

Installation Steps

1. Disconnect power from all equipment.

2. (Optional) Mount the unit. Rack mount the scaler using the attached brackets (see the illustration at right). For tabletop placement, remove the brackets from the right and left sides and attach the provided rubber feet.

3. Connect video inputs. Connect video input devices to the appropriate connectors in the rear panel Video Input section (B through E in the diagram above).

zz Video inputs 5 and 6: RGB or YUV component —

Connect one or two RGBHV, RGBS, RGsB, RGBcvS, YUVi,
or YUVp/HDTV video sources to these female 15-pin HD
connectors (shown below). These connectors feature EDID
emulation.	3	2
		1
	14	13	MBD 249
			2U Rack Mounting

Bracket (Pre-attached)

NOTE: (Optional) To obtain one or two more RGB/YUV inputs, you can connect an Extron DVIIM-VGAF/DVIIF

DVI and Analog Breakaway (Y) cable to either or both DVI-I input connectors. Each Y cable provides an additional RGB VGA connector and DVI-I connector (see ”Breakaway cable” on the next page).

1