Extron electronic VNR 100 setup guide Getting Started with VNM Enterprise Controller, Logout

VNR 100 • Setup Guide (Continued)

1.Use a computer connected to the same network as the VNR 100. In the browser address bar, enter the IP address of the recorder, followed by a colon (:) and the port number. By default, this is 192.168.254.254:8080. Contact your network administrator to be sure these values have not changed.

The login screen opens (see figure at right).

2.Enter the Username and Password.

NOTE: By default, both the Username and Password are config.

3.Click Login. The VNR 100 Recorder Settings page opens (see figure at right).

4.Enter the IP Address, Subnet Mask, and Gateway Address of the recorder.

5.Enter the Controller IP address, Controller port number and maximum transmission unit (MTU) setting for the controller. Contact your network administrator to ensure you have the correct values.

ATTENTION: The VNM Enterprise Controller port number is used by all VN-Matrix devices to communicate with the VNM Enterprise Controller. The value should only be changed if the VNM Enterprise Controller has been configured to accept communications on a different port number.

Under normal circumstances, the setting should remain at the default value (5432).

6.Enter a New password and Confirm New password.

7.Click Apply Changes to save the settings (or Cancel Changes to exit without saving the information).

			Logout
		VNMatrix recorder settings
		Network settings [eth0]
IP Address		192.168.254.254
Subnet Mask		255.255.255.0
Gateway		192.168.254.253
		Recorder settings
Serial		1111999
Controller IP		192.168.254.254
Controller port		5432
MTU		1500
		User settings
New password
Confirm New password
		Data disk
Umount	status:	mounted to /home/matrix_rec/Recording_Files
Disk free space:		19GB->98% used
Format		formated to ext3
		Apply Changes	Cancel Changes

Getting Started with VNM Enterprise Controller

The VNM Enterprise Controller must be on the same network as the VNR 100.

1.	Use a PC on the same network as the controller to access the controller website. In
	the browser address bar, enter the controller IP address. The Login screen opens (see
	figure at right).
2.	Enter the Username and Password.
	NOTE: By default, for the VNM Enterprise
	Controller, the Username is admin. Leave
	the Password blank (no entry is required).
3.	Click Login. The Enterprise Controller device list
	opens (see the figure to the right).
4.	Check the box next to the VNR 100 recorder. A
	series of action buttons appear at the bottom of
	the screen (see figure below).
	See the Enterprise Controller User Guide (at
	www.extron.com) for complete information
	about configuring and using the VNR 100.

Extron Headquarters		Extron Europe	Extron Asia	Extron Japan	Extron China	Extron Middle East	Extron Korea	Extron India
+1.800.633.9876 (Inside USA/Canada Only)		+800.3987.6673	+65.6383.4400	+81.3.3511.7655	+86.21.3760.1568	+971.4.299.1800	+82.2.3444.1571	1800.3070.3777
Extron USA - West	Extron USA - East	(Inside Europe Only)	+65.6383.4664 FAX	+81.3.3511.7656 FAX	+86.21.3760.1566 FAX	+971.4.299.1880 FAX	+82.2.3444.1575 FAX	Inside India Only
+1.714.491.1500	+1.919.850.1000	+31.33.453.4040						+91.80.3055.3777
+1.714.491.1517 FAX	+1.919.850.1001 FAX	+31.33.453.4050 FAX						+91.80.3055.3737 FAX

© 2013 Extron Electronics All rights reserved. www.extron.com	68-2237-50 Rev. A
4	05 13