Gigabyte GA-7VAC manual Halt on, Base Memory, Extended Memory

Page 32

English

FHalt on

The category determines whether the computer will stop if an error is detected during power up.

8NO Errors

The sy stem bootw ill not stop for any error thatmay be detected

 

and y ou will be prompted.

8All Errors

Whenev er the BIOS detects a non-fatal error the sy stem w ill be stopped.

8All, But Keyboar

The sy stem bootw ill not stop for a key board error; it w ill stop for

 

all other errors. (Defaultv alue)

8All, But Diskette

The sy stem boot will notstop for a disk error; it w ill stop for all

 

other errors.

8All,But Disk/Key

The sy stem boot w ill notstop for a key board or disk error; it will

 

stop for all other errors.

Memory

The category is display -only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

The value of the base memory is typically 512 K for sy stems with 512 K memory installed on the motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the P OST. This is the amount of memory located above 1 MB in the CPU’s memory address map.

GA-7VA-C Motherboard

- 28 -

Image 32
Contents AGP 4X notch Page Declaration of Conformity Product Name Motherboard Model NumberGA-7VA Supplementary InformationGA-7VA-C Table of Content Table of Content Item Checklist Installing the motherboard to the chassis…Chapter Introduction Bios GA-7VA-C Motherboard Layout Hardware Installation Process StepOFF SW1SW1 CPU Clock Pin1 indicator 3CPU Heat Sink Installation Install memory modules DDRInstall expansion cards DDR IntroductionUSB PS/2 Keyboard and PS/2 Mouse ConnectorUSB Connector Audio Connectors Parallel Port ,VGA port and Serial Ports ComaGame /MIDI Ports Coma CO MBConnectors Introduction 3ATXPOWER ATX Power 1CPUFAN CPU FAN Connector2SYSFAN System FAN Connector 4IDE1/ IDE2 IDE1/IDE2 Connector 5FDD Floppy ConnectorIDE2 IDE1MSG+ PW+ PW SPK HD+ HD RES RES+ 8FPANEL 2x10 pins connector9BATTERYBattery 10FAUDIO Faudio Connector 13AUXIN AUX In Connector12CDIN CD 14SPDIF SPDIFOutFUSB1 FUSB2 16F USB1 / FUSB2 Front USB Connector, YellowVC C Spdif GND English Bios Setup Main Menu For example Bios Ver. F6 Power Management S etup PnP/PCI Configurations Load Fail-Safe Defaults Load Optimized DefaultsTime Standard Cmos FeaturesDate FDrive a / Drive B Floppy 3 Mode Support for Japan AreaIDE Primary Mas ter, S lave / Secondary Master, Slave Halt on MemoryBase Memory Extended MemoryAdvanced Bios Features FFirst / S econd / Third Boot deviceFInit Display First Boot Up Floppy SeekPas sword Check Integrated Peripherals Bios Setup Integrated PeripheralsOnChip IDE Channel0 OnChip IDE Channel1IDE1 Conductor Cable IDE2 Conductor CableFusb 2.0 Controller US B Keyboard S upportUS B Mouse Support FOnboard Serial PortFParallel Port Mode FGame Port AddressFMidi Port Address Midi Port IRQPower Management Setup FPower LED in S1 State Keyboard Power OnAcpi Suspend Type Soft-off by PwrbtnPME Event Wak e up Mouse Power OnFResume by Alarm PnP/PCI Configurations FPCI1/PCI5 IRQ AssignmentFPCI2 IRQ Ass ignment FPCI3 IRQ Ass ignmentPC Health Status CRes et Case Open Status CCase OpenedCurrent CPU Temperature C CPU Shutdown TemperatureCurrent CPU FAN / S YS TEM FAN Speed RPM Fan Fail Warning CPU / SystemCPU Host Frequency MHz By switch SW1 Frequency/Voltage ControlSpread spectrum Modulated CPU Host Clock ControlPCI/AGP Frequency MHz Dram Clock MHzCPU OverVoltage Control AGP OverVoltage ControlTop Performance DisabledEnabled Load Fail-Safe Defaults Load Fail-Safe Defaults? Y/N ?NLoad Optimized Defaults Load Optimized Defaults? Y/N ?NSet Supervisor/User Password Enter PasswordSave & Exit Setup Save to Cmos and Exit Y/N? YExit Without Saving Quit Without Saving Y/N? NEnglish English Technical Reference Bios Flash Procedureyte @BIOSTM Program to flash Bios StepEnglish English English English Hifg Amibios Setup Bios Features Setup 7VTX.F4 FLASH841.EXE EXIT? English Congratulate you have accomplished the Bios flash procedure What is Q-Flash Utility? How to use Q-Flash?Load Bios From Floppy XXXX.XXEnglish English @ Bios Introduction Easy TuneTM 4 Introduction Stereo Speakers Connection and Settings 6-Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode SURROUND-KIT access analog output to rear Basic &Advanced 6 Channel Analog Audio Output ModeNotes Spdif Output Device Optional Device Memo English Appendix Picture below are shown in Windows XP CD driver versionUSB Patch Driver VIA USB2.0 DriverEnglish Appendix B RealTek AC97 Audio Driver Appendix C EasyTune4 Utilities Installation Appendix D Acronyms LBA LEDMidi MTHAMR / CNR Technical Support/RMA SheetHDD CD-ROM DVD-ROM MShould you need to find new support list, pls refer to MIC RON DDRSamsung DDR AdataTroubleshooting END English Memo English English English