Gigabyte GA-M55SLI-S4 user manual Battery, Spdifi Spdif

Page 30

English

17) BATTERY

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

If you want to erase CMOS...

1. Turn off the computer and unplug the power cord.

2. Gently take out the battery and put it aside for about one minute. (Or you can use a metal object to connect the positive and negative pins in the battery holder to makethem short for five seconds.)

3. Re-install the battery.

4. Plug the power cord in and turn on the computer.

18)SPDIF_I (SPDIF In)

Use SPDIF IN feature only when your device has digital output function. Be careful with the polarity of the SPDIF_IN connector. Check the pin assignment carefully while you connect the SPDIF cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional SPDIF cable, please contact your local dealer.

 

 

 

 

 

 

 

Pin No.

Definition

1

 

 

 

 

 

 

1

Power

 

 

 

 

 

 

 

2

SPDIFI

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

GND

GA-M55SLI-S4 Motherboard

- 30 -

Image 30
Contents GA-M55SLI-S4 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-M55SLI-S4 Motherboard Layout Block Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Setup of SLI Scalable Link Interface Configuration Before You BeginEnabling SLI Mode English English I/O Back Panel Introduction Surround Speaker Out Rear Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out Side Speaker OutATX12V/ATX Power Connector PCIE12V Power Connector 6 Cpufan / SYSFAN/ Pwrfan Cooler Fan Power ConnectorFDD FDD Connector IDE1 / IDE2 IDE ConnectorFaudio Front Audio Panel Connector Cdin CD In Connector Fpanel Front Panel JumperUSB1 / FUSB2 / FUSB3 Front USB Connector Pwrled15 F11394 / F21394 Ieee 1394 Connector Clrcmos Clear CmosBattery Spdifi SpdifCI Chassis Intrusion, Case Open English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D8 F12 For Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationTime IDE Channel 0 Master, Slave, IDE Channel 1 Master, SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive aHalt on Hard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Away ModeInit Display First On-Chip IDE Channel0 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel1On-Chip MAC Lan On-Chip LAN Boot ROMIDE Prefetch Mode NV Sata RAID functionSmart LAN LAN Cable Diagnostic Function When LAN Cable Is Functioning NormallyOnboard 1394 Function Parallel Port ModeECP Mode Use DMA Onboard Serial PortPower Management Setup Power On By Mouse PnP/PCI Configurations PCI 2 IRQ AssignmentPCI 1 IRQ Assignment PC Health Status CPU Warning Temperature CPU Smart FAN ModeCPU Smart FAN Control Note MB Intelligent TweakerM.I.T CPU clock Ratio CPU Spread SpectrumPcie Clock Robust Graphics BoosterTop Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish EasyTune 5 Introduction User Interface OverviewXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer Shadow Appendix Step Save and exit Bios Setup GA-M55SLI-S4 Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Introduction of audio connectors Stereo Speakers Connection and Settings5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English English Troubleshooting English English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System