Apple 1705 Display manual Chapter

Page 10

myour display has been dropped or the case has been otherwise damaged

myou suspect that your display needs service or repair

myou want to clean the case (use only the recommended procedure described in “Care and Cleaning” in Chapter 4)

IMPORTANT The only way to disconnect power completely is to unplug the power cord. Make sure at least one end of the power cord is within easy reach so that you can unplug the display when you need to.

Be sure that you always:

mKeep your display away from sources of liquids, such as wash basins, bathtubs, shower stalls, beverages, and so on.

mDon’t set anything on top of the display (such as a book or cup).

mKeep the display’s vents free from obstruction.

mProtect your display from dampness or wet weather, such as rain, snow, and so on.

mRead all the installation instructions carefully before you plug your display into a power source.

mKeep these instructions handy for reference by you and others.

mFollow all instructions and warnings dealing with your system.

WARNING Never remove the cover from the display or you may come in contact with hazardous voltage levels capable of causing serious injury and possibly death.

WARNING Electrical equipment may be hazardous if misused. Operation of this product, or similar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical product and do not permit them to handle any cables.

2Chapter 1

Image 10

Contents MultipleScan 1705Display Apple Computer, Inc Contents Adjusting the Picture Contents FCC statement Radio and television interference DOC statement Vcci statementPage Setting Up Important safety instructionsChapter What about electromagnetic emissions? Getting ready to set up Your Apple Multiple Scan Display at a glance Power button Contrast controlDisplay cable Choosing a good location for your display Positioning the displayDo you need a video card? Shoulders relaxedConnecting the display to your computer Using more than one displaySetting Up To turn on the display for the first time Turning the display onStart up your computer Installing the display software Disk’s icon appears on the desktopClick the Install button Installer screen appearsRead the Welcome screen and click OK Using the Display Software About the Control StripWorking with the Control Strip Choose Control Panels from the Apple K menu Changing screen resolutionWindow opens showing all the control panels Make the following choices in the control panelOther things you can do with the Monitors control panel Conserving energy What happens after you turn on the energy saving featureClose the control panel Using ColorSync Using Energy Saver with a screen saverClick Set Profile ColorSync control panel appearsClick a monitor name to select it To show or hide the Control Strip, follow these steps Configuring the Control StripShowing and hiding the Control Strip Control Strip control panel appearsBox appears To change the keyboard command, click Define hot keyPress the keys you want to use, then click OK Changing the font in Control Strip menus Adjusting the Picture Accessing the display’s controlsMaking adjustments to the picture Use this controlUse these controls Follow these steps Follow these stepsVertical center icon goes on Width icon goes onAdjusting the shape of the picture Picture curvature icon goes onResetting controls to the factory settings Page Tips and Troubleshooting Care and cleaningTo clean the screen of the monitor TroubleshootingProtecting your monitor from theft Make sure that the power cord is plugged in properly Monitor’s power indicator light doesn’t come onScreen is dark or appears dim Screen flickersScreen image is off center No colors appear on the screenScreen image is too large or too small After many hours of use, the screen image appears dim You can’t control the sound volume of a CDYou don’t see the monitor resolution you want Over time, you experience eyestrainAfter you change the screen resolution, icons move When you change resolutions, the monitor goes blank You see two resolution options labeled 640x870 75 HzMonitor does not go to sleep Appendix a Technical Information Input signalsPower saving feature Picture tubeActive video image area Adjusted at the factory for the following standard modesUser controls Input electrical requirementsTemperature WeightDimensions Humidity noncondensingPin miniature D-type connector Display cable specificationsPin Output signal Appendix B Setting Up for IBM PC-Compatible Users Appendix B Resolution Vertical refresh rate hertz CompatibilityPower cord Choosing a good location for your display Connecting the display to your IBM PC-compatible computer Connecting the power cord Connecting the display cable Display port on IBM PC-compatible Using the display Apple Computer, Inc