Tripp Lite APSINT Series owner manual Feature Identification

Page 3

Feature Identification

Identify the premium features on your specific model and quickly locate instructions on how to maximize their use.

1 Configuration DIP Switches: optimize Inverter/Charger operation depending on your application. See Configuration Section for setting instructions.

2Operating Mode Switch: controls Inverter/Charger operation. The “AUTO/REMOTE” setting ensures your equipment receives constant, uninterrupted AC power. It also enables the Inverter/Charger to be remotely monitored and controlled with an optional remote module (Tripp Lite model APSRM4, sold separately). The “CHARGE ONLY” setting allows your batter- ies to return to full charge faster by turning the inverter off which halts battery discharging. See Operation Section for set- ting instructions.

8Hardwire AC Input/Output Terminal Strip (not on corded models): securely connects the Inverter/Charger to facility or vehicle electrical system. See Input/Output Connection Section for connection instructions.

9Resettable Circuit Breaker: protects your Inverter/Charger against damage due to overload. See Operation Section for resetting instructions.

10Remote Control Module Connector: allows remote monitoring and control with an optional module (Tripp Lite model APSRM4, sold separately). See remote module owner’s manu- al for connection instructions.

3Operation Indicator Lights: intuitive “traffic light” signals show whether the Inverter/Charger is operating from AC line power or DC battery power. It also warns you if the connected equipment load is too high. See Operation Section for instruc- tions on reading indicator lights.

4Battery Indicator Lights: intuitive “traffic light” signals show approximate charge level of your battery. See Operation Section for instructions on reading indicator lights.

5DC Power Terminals: connect to your battery terminals. See Battery Connection Section for connection instructions.

6AC Output Receptacles (not on hardwire models): IEC-320 output receptacle(s) allow you to connect equipment that you would normally plug into a utility outlet. Select models also include a Universal AC Output Adapter which allows you to connect equipment with a wide variety of plug styles.

7AC Input Receptacle (not on hardwire models): IEC-320 input receptacle connects the Inverter/Charger to any source of utility or generator-supplied AC power when used with a user- supplied cable with country-specific plug.

11Battery Charge Conserver (Load Sense) Control (available on select models): conserves battery power by setting the low-load level at which the Inverter/Charger’s inverter automati- cally shuts off. See Configuration Section for setting instructions.

12Main Ground Lug: properly grounds the Inverter/Charger to earth ground or to vehicle or boat grounding system. See Battery Connection Section for connection instructions.

13Thermostatically-Controlled Cooling Fan: quiet, efficient fan regulates internal temperature and prolongs equipment service life. Fan runs intermittently depending on temperature and load.

14Hardwire AC Input/Output Cover Plate

Dead Battery Startup Feature (for all models, internal, not shown): internal circuitry allows you to start up the Inverter/Charger even with a dead battery connected to the unit. As long as the Inverter/Charger is connected to a live utility- or generator-supplied AC power source, the Inverter/Charger will pass through AC power to connected equipment and charge con- nected batteries.

13

1

4

10

3

2

13

1

4

10

3

2

11

9

 

 

 

 

12 Rear Mounted, Not Shown

 

 

 

“FOR USE WITH COPPER WIRE ONLY”

9

 

 

 

HOT IN

 

 

 

NEUTRAL

IN

 

6

 

GROUND

IN

 

 

GROUND

OUT

 

 

 

HOT OUT

 

 

 

 

NEUTRAL

OUT

5

 

5

8

14

7

12

Front View (2012, 2424 & 3636 Hardwire Models).

Front View (750 & 1250 Corded Model)

 

3A

Image 3
Contents Apsx & Apsint Series DC-to-AC Inverter/Chargers ContentsLimited Warranty Important Safety InstructionsFeature Identification Switch Modes Indicator LightsOperation Group B DIP Switches ConfigurationSet Configuration DIP Switches Group a DIP SwitchesSelect Battery Charger-Limiting Select Battery Type Battery SelectionVehicular and Non-Vehicular Horizontal Mount MountingNon-Vehicular or Vehicular Battery ConnectionAC Input/Output Connection Service MaintenanceTroubleshooting 200608120 93-2608EN