Tripp Lite B030-002-R user manual FCC Radio / TV Interference Notice, Scan Mode Auto Scan mode

Page 5

Troubleshooting

Problem

Cause

Solution

Video

A power source

Move the device that is

Problems

such as a power

creating the electromagnetic

 

panel or poorly

interference, or move the KVM

 

insulated device is

switch and/or its cables.

 

too close to the

 

 

KVM switch or its

 

 

cables

 

Keyboard Not

Keyboard needs

Unplug the keyboard from the

Responding*

to be reset

Switch, then plug it back in.

 

 

 

 

Switch needs

Turn off the PCs. Wait 5

 

to be reset

seconds; then turn the PCs on.

 

 

 

 

Switch is in “Auto

Press the [Spacebar] to exit

 

Scan” Mode

“Auto Scan” mode.

 

 

 

 

Switched between

Shut down the PC and reboot

 

PCs during boot-up

without switching between PCs.

 

procedure

 

 

 

 

*Some notebook computers, notably the IBM® Thinkpad® and Toshiba® Tecra®, have trouble working with a switch when their mouse and keyboard ports are used simultaneously. To avoid this problem, only connect the mouse port or the keyboard port to the switch. If you connect the mouse port, you will need to use the notebook’s keyboard when the notebook is the active computer. These switches are designed to work with PS/2 keyboards. Older XT

(84 key) and AT keyboards will not work.

FCC Radio / TV Interference Notice

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause inter- ference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter- ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference using one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and the receiver; connect the equip- ment into an outlet on a circuit different from that which the receiver is connected; consult the dealer or an experienced radio/television technician for help. The user must use shielded cables and connectors with this product. Any changes or modifi- cations to this product not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

3-YEAR LIMITED WARRANTY

TRIPP LITE warrants its products to be free from defects in materials and workman- ship for a period of three (3) years from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an author- ized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been dam- aged by accident, negligence or misapplication or has been altered or modified in any way.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POS- SIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

TRIPP LITE has a policy of continuous improvement. Specifications are subject to change without notice.

8

9

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Port KVM Switch with Built-In Cables PS/2 Type Components FeaturesSystem Requirements Operation Hot Key Port Selection InstallationTroubleshooting SpecificationsFCC Radio / TV Interference Notice Scan Mode Auto Scan modeCaracterísticas Nº de modelo Serie B030-002-RInstalación Requisitos del sistemaComponentes Operación Selección de puerto con Teclas de acceso directo Apéndice EspecificacionesGarantíalimitadade Tres Años Commutateur KVM 2-port Avec câbles intégrés Type PS/2 Caractéristiques Configuration du systèmeComposants Spécifications FonctionnementAnnexe Problème Cause SolutionAvis de brouillage radioélectrique de la FCC Garantie Limitée DE 3 ANS

B030-002-R specifications

The Tripp Lite B030-002-R is a highly regarded KVM (Keyboard, Video, Mouse) switch that allows users to control two computers from a single set of peripherals effortlessly. This device is particularly useful in environments where space is limited, such as server rooms, data centers, or even small office setups.

One of the primary features of the B030-002-R is its support for a wide range of video resolutions, including high-definition formats up to 1920 x 1200. This ensures that users can enjoy crisp and clear visuals, making it ideal for applications requiring detailed graphics. The KVM switch supports both USB 1.1 and USB 2.0, accommodating a variety of devices from keyboards and mice to printers and external storage.

The B030-002-R is equipped with a user-friendly interface that includes a push-button switch located on the front panel. This design allows for quick and easy switching between connected computers without the need for complex configurations. Additionally, the KVM switch supports hot-key switching, which lets users toggle between systems using keyboard shortcuts. This feature enhances efficiency by eliminating the inconvenience of reaching for the switch.

Another significant characteristic of the Tripp Lite B030-002-R is its broad compatibility with various operating systems, including Windows, macOS, and Linux. This versatile compatibility ensures that users can integrate the switch seamlessly into their existing setups without requiring specific drivers or software.

In terms of build quality, the B030-002-R is built to last, featuring a sturdy design that can withstand the rigors of daily use. The switch is compact, making it easy to integrate into any workspace without cluttering the area. Additionally, the device has a reliable power source, receiving power from connected USB devices, eliminating the need for external power adapters.

In summary, the Tripp Lite B030-002-R KVM switch is a high-performance device that offers reliable and efficient control over two computers. With its support for high-definition video, user-friendly interface, broad compatibility, and durable construction, it stands out as an essential tool for anyone looking to enhance their productivity and streamline their workspace. Whether for professional use or personal projects, the B030-002-R delivers convenience and functionality.
Top Page Image Contents