Tripp Lite B006-VU4-R owner manual Hotkey Function Hotkey Command, Start Auto Scan with

Hotkey Operation

The B006-VU4-R allows the KVM switch to be controlled via the keyboard. The table below describes the available Hotkeys and their functions. Hotkey commands require that the [Shift] key be held down while the remaining hotkeys are pressed. The first two hotkeys will always be [Scroll Lock], [Scroll Lock] or [Ctrl], [Ctrl]. [Scroll Lock], [Scroll Lock] is the default. It can be changed to [Ctrl], [Ctrl] using the Change Hotkey Mode Activation Command in the following table.

Hotkey Function	Hotkey Command
Initiate Hotkey	Hold down the [Shift] key and hit [Scroll Lock], [Scroll Lock]. Once Hotkey
Mode	Mode has been initiated, your keyboard’s [Scroll Lock] and [Caps Lock] LEDs
	will blink in succession. Press the [Esc] key to exit Hotkey Mode.
	Note: The default command uses [Scroll Lock], [Scroll Lock]. This can be
	changed to [Ctrl], [Ctrl] using the Change Hotkey Mode Activation Command.
Switch to Next Port	Initiate Hotkey Mode by holding down the [Shift] key and hitting [Scroll Lock],
	[Scroll Lock]. Once initiated, press the [Enter] key to switch to the next port.
	Note: The KVM will switch the consoles focus to the next port, regardless of
	whether a computer is connected to it or not.
Switch to Specific	Initiate Hotkey Mode by holding down the [Shift] key and hitting [Scroll Lock],
Port	[Scroll Lock]. Once initiated, press n, [Enter] (n=port number; 1, 2, 3 or 4).
	Note: The KVM will switch to the selected port, regardless of whether a
	computer is connected to it or not.
Start Auto Scan	Initiate Hotkey Mode by holding down the [Shift] key and hitting [Scroll Lock],
	[Scroll Lock]. Once initiated, press [a], [Enter]. The KVM begins scanning each
	port at 5 second intervals. To stop scanning at the currently selected computer,
	press the [Esc] key.
	Note: The KVM switch will scan each port whether a computer is connected to
	the port or not.
Start Auto Scan with	Initiate Hotkey Mode by holding down the [Shift] key and pressing [Scroll
a Specific Duration	Lock], [Scroll Lock]. Once initiated, press [a], n, [Enter] (n=scan duration
	between 1 and 99 seconds). Press the [Esc] key to stop scanning at the currently
	selected computer.
	Note: The KVM switch will scan each port, whether a computer is connected to
	the port or not.
Initiate Setting Mode	Hold down the [Num Lock] key, press and release the minus [-] key, and release
	the [Num Lock] key. When Setting Mode is initiated, your keyboard’s [Caps
	Lock] and [Scroll Lock] LEDs will blink in succession. Press the [Esc] key at
	any time to exit Setting Mode.
	Note: The default command is [Num Lock], minus [-]. This can be changed to
	[Ctrl], [F12] using the Change Setting Mode Activation Command.
Disable/Enable	Initiate Setting Mode by holding down the [Num Lock] key, pressing and
Hotkey Commands	releasing the minus [-] key and releasing the [Num Lock] key. Once initiated,
	press [x], [Enter] to Disable or Enable hotkey commands. When hotkey
	commands are disabled, the KVM ports are accessible via pushbutton only.
	Setting Mode commands will still be accessible.
Change Setting	Initiate Setting Mode by holding down the [Num Lock] key, pressing and
Mode Activation	releasing the minus [-] key, and releasing the [Num Lock] key. Once initiated,
Command	press [h] to switch to [Ctrl], [F12]. When set at [Ctrl], [F12], change the Setting
	Mode Activation Command back to [Num Lock], minus [-] by holding down
	the [Ctrl] key, pressing and releasing the [F12] key, and releasing the [Ctrl] key.
	Once initiated, press [h] to switch to [Num Lock], minus [-].

5