StarTech.com SV231UADVI instruction manual Keyboard Hotkey Command Reference Chart

Page 7

Instruction Manual

Keyboard Hotkey Command Reference Chart

Command Name

Hotkey Sequence

Description

 

 

 

 

 

Switches access to the computer connected to the

Select active computer

[ScrLk]+[ScrLk]+[x]

corresponding port number on the KVM.

 

 

([x]= a number on the keyboard)

 

 

 

 

 

Switches which corresponding port number has access to

Select USB hub control

[ScrLk]+[ScrLk]+[Fx]

the to the devices connected to the KVM’s USB hub.

 

 

([Fx] = Function key: F1=Port 1, F2=Port 2, etc.)

 

 

 

 

 

Switches which port’s speaker and microphone output is

Select Audio/Mic output

[ScrLk]+[ScrLk]+[Fy]

active at the console.

 

 

([Fy] = Function key: F5=Port 1, F6=Port 2, etc.)

 

 

 

Bind computer and USB hub

 

When either the select active computer or select USB hub

[ScrLk]+[ScrLk]+[Z]

control commands are executed, both functions are

control (default)

 

switched to the selected port.

 

 

 

 

 

Unbind computer and USB

 

The computer control and USB hub control can be

[ScrLk]+[ScrLk]+[X]

executed separately; KVM control and USB hub control

hub control

 

control can be assigned to different ports at one time.

 

 

 

 

 

Bind computer and Audio/Mic

 

When either the select active computer or select

[ScrLk]+[ScrLk]+[Q]

audio/mic output control commands are executed, both

control (default)

 

functions are switched to the selected port.

 

 

 

 

 

 

 

The computer control and USB hub control can be

Unbind computer and

[ScrLk]+[ScrLk]+[W]

executed separately; KVM control and Audio/Mic output

Audio/Mic output control

control control can be assigned to different ports at one

 

 

 

time.

 

 

 

Select next/previous port

[ScrLk]+[ScrLk]+[arrow]

Selects the next (up arrow key) or previous (down arrow

key) numbered port for control.

 

 

 

Select previous port

[ScrLk]+[ScrLk]+[BkSp]

Selects the most recent previously active port.

 

 

 

Beep sound on/off

[ScrLk]+[ScrLk]+[B]

Enables/disables audible responses from the KVM.

 

 

 

Define new hotkey sequence

[ScrLk]+[ScrLk]+[H]+[y]

Change the standard [ScrLk] hotkey to a new value (see

 

 

below).

 

 

 

Autoscan

[ScrLk]+[ScrLk]+[S]

Automatically switch active ports in sequence every 10

seconds. (Press any key to cancel.)

 

 

 

 

 

Autoscan with programmable

[ScrLk]+[ScrLk]+[S]+[z]

Autoscan with a delay other than 10 seconds (see below).

delay

 

Press any key to cancel.

Binding/Unbinding control: By default the switch will automatically switch USB hub and audio control to the KVM port you select to control (bound). If you choose to “unbind” control, you can assign control of the audio and/or USB hub to a port other than the active computer using the commands above.

Valid hotkey sequences: If you enter the “Define new hotkey sequence” command ([ScrLk]+[ScrLk]+[H]+[y] the value of [y] replaces the [ScrLk]+[ScrLk] command with one of the following:

[CapsLk] = [CapsLk]+[CapsLk] [Esc] = [Esc]+[Esc]

[F12] = [F12]+[F12]

[NumLk] = [NumLk]+[NumLk]

[ScrLk] = [ScrLk]+[ScrLk] (if another key sequence has been enabled)

Programmable Autoscan delay time: [z] can be any one of the following values:

1=10 sec., 2=20 sec. through 9=90 sec., 0=100 sec.

Note: Apple computers will need to be programmed using an IBM-compatible keyboard that has a Scroll Lock key.

4

Image 7
Contents USB DVI KVM Switch FCC Compliance Statement Table of Contents System Requirements Introduction FeaturesContents Before You BeginInstalling the KVM Switch InstallationConnecting Computers to the KVM Switch Using the KVM Switch Command Name Hotkey Sequence Description Keyboard Hotkey Command Reference ChartAccessory Products from StarTech.com Limitation of Liability Technical Support Warranty InformationAbout StarTech.com