Pelco PV130 RS-422 Warranty and Return Information, Common Causes for Control Problems No Control

Page 2

Testing (Refer to PV1000 Instruction/Operation Manual)

1.Ensure that the PV1016 Transmitter DIP switch settings or the PV1004 Transmitter programming are correct for the telemetry type required by the receiver.

2.Ensure that the PV1000 Transmitter is properly programmed for the COM 2 port baud rate and parity required by the receiver.

3.Confirm receiver PTZ control from a PV1016 Transmitter with front panel keyboard (while off-line) or from the PV1016 Receiver (while on-line). Check for smooth operation.

Common Causes for Control Problems

No Control

 

 

 

 

 

Converter-to-receiver twisted pair connections reversed or

• Transmitter DIP switch settings or programming incorrect for

receiver type.

wired incorrectly.

• Transmitter COM 2 port baud rate and/or parity programming

• Power supply +12 VDC and GND connections to converter

incompatible with receiver type.

reversed.

Erratic Control

 

 

 

 

• Cabling between converter and receiver incompatible with

• Wire distance between converter and receiver exceeds

RS-422 operation.

4,000 feet.

• Wire distance between converter and receiver requires suitable

• Video coax cable has Coaxitron® or other “up-the-coax”

termination at receiver.

control information present.

Figure 2. RS-422 Circuit PV130

RS-422

Wiring Diagram

 

 

TX-

 

 

RX-

 

 

TX+

 

 

RX+

 

 

RX-

 

 

TX-

 

 

RX+

 

 

TX+

 

 

GND

 

GND

100

100

 

WARRANTY AND RETURN INFORMATION

WARRANTY

The above warranty provides the Dealer with specific legal rights. The Dealer may

Pelco will repair or replace, without charge, any merchandise proved defective in

also have additional rights, which are subject to variation from state to state.

material or workmanship for a period of one year after the date of shipment. Excep-

 

tions to this warranty are as noted below:

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

 

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the

• Three years on Genex® Series (multiplexers, server, and keyboard).

following information:

• Two years on cameras and all standard motorized or fixed focal length lenses.

 

• Two years on Legacy®, Camclosure™ Camera Systems, CM6700/CM8500/

1. Model and serial number

CM9500/CM9750/CM9760 Matrix, PelcoVision®, DF5 Series and DF8 Fixed Dome

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

products.

3. Details of the defect or problem

• Two years on Spectra® and Esprit™, including when used in continuous motion

 

applications.

If there is a dispute regarding the warranty of a product which does not fall under the

• Two years on WW5700 series window wiper (excluding wiper blades).

warranty conditions stated above, please include a written explanation with the

• Six months on all pan and tilts, scanners or preset lenses used in continuous

product when returned.

motion applications (that is, preset scan, tour and auto scan modes).

 

 

Method of return shipment shall be the same or equal to the method by which the

Pelco will warrant all replacement parts and repairs for 90 days from the date of

item was received by Pelco.

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to

RETURNS

Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration,

normal wear, or accident are not covered under this warranty.

In order to expedite parts returned to the factory for repair or credit, please call the

 

factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA

Pelco assumes no risk and shall be subject to no liability for damages or loss result-

number if returned for credit, and RA number if returned for repair). Goods returned

ing from the specific use or application made of the Products. Pelco’s liability for any

for repair or credit should be clearly identified with the assigned CA/RA number and

claim, whether based on breach of contract, negligence, infringement of any rights

freight should be prepaid. All merchandise returned for credit may be subject to a

of any party or product liability, relating to the Products shall not exceed the price

20% restocking and refurbishing charge.

paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any

 

special, incidental or consequential damages (including loss of use, loss of profit

Ship freight prepaid to: Pelco

and claims of third parties) however caused, whether by the negligence of Pelco or

3500 Pelco Way

otherwise.

Clovis, CA 93612-5699

REVISION HISTORY

Manual #

Date

Comments

C1919M

9/97

Original version.

C1919M-A

3/00

Revised installation instructions and Figure 1. Added Figure 2.

C1919M-B

7/00

Corrected RX polarity in Figure 1.

C1919M-C

11/00

Revised drawings to reflect label change.

® Pelco, the Pelco logo, Spectra, Genex, Legacy, Coaxitron, and PelcoVision are registered trademarks of Pelco.

© Copyright 2000, Pelco.

™ Esprit and Camclosure are trademarks of Pelco.

All rights reserved.

Image 2
Contents Description InstallationConnecting the Power Supply See Figure Control ConnectionsWarranty Warranty and Return InformationCommon Causes for Control Problems No Control Erratic Control
Related manuals
Manual 2 pages 27.33 Kb

PV130 RS-422 specifications

The Pelco PV130 RS-422 is a cornerstone in the realm of video surveillance and camera control systems. Known for its robust performance and reliability, the PV130 is designed to facilitate seamless communication between controllers and cameras in diverse security environments.

One of the main features of the Pelco PV130 is its RS-422 communication protocol. This protocol enables long-distance transmission over twisted pair cable, offering improved noise immunity and high data rates. As a result, the PV130 allows for the control of multiple Pelco cameras from a single control point, making it an efficient choice for extensive surveillance installations.

The device supports various types of cameras, including fixed, PTZ (pan-tilt-zoom), and dome configurations, granting users flexibility in the type of surveillance they wish to implement. Thanks to its support for telemetry control, users can manipulate camera movements and settings remotely, adjusting the view as necessary for maximum coverage and detail.

Another significant characteristic of the PV130 is its ease of integration with other Pelco systems and third-party devices. The PV130 is crafted with versatility in mind, allowing it to interface effectively with different types of control systems, which is essential for modern security solutions that often encompass varied technologies.

With advanced features such as programmable presets and tours, users can customize camera behaviors for specific scenarios. This enhances surveillance efficiency, enabling operators to monitor multiple areas systematically. The inclusion of on-screen display (OSD) for various camera parameters further simplifies operation and provides essential feedback to the user.

Durability is also a hallmark of the Pelco PV130. Built to withstand the rigors of daily surveillance operations, the unit exhibits a robust design that can endure various environmental conditions. This characteristic makes it suitable for both indoor and outdoor setups.

In addition to these features, the Pelco PV130 is backed by comprehensive support from Pelco, ensuring users have access to resources for troubleshooting and system enhancements. Overall, the Pelco PV130 RS-422 stands out as a reliable, versatile, and user-friendly solution for modern video surveillance needs, integrating advanced technologies to enhance security operations across various environments. Whether for small businesses or large enterprises, the PV130 is equipped to meet diverse surveillance demands efficiently.