Network Technologies MAN049 manual T R O D U C T I O N, T E R I a L S, Installation

I N T R O D U C T I O N

The KEEMUX-P2 switch allows one user to access two PS/2 computers with only one keyboard, monitor and mouse. Internal auto-boot circuitry allows both computers to boot simultaneously and error-free without the need for a keyboard, monitor and mouse on each computer.

M A T E R I A L S

Materials Supplied with this kit:

1.NTI PS/2 KVM Switch

Materials Not Supplied, BUT REQUIRED:

1. A set of 2 cables for each computer being connected to the switch must be used:

PS/2 computer to switch	1.	VEXT-xx-MM (high res) or VINT-xx-MM (low res) for video interface
	2.	(1) VVKINT-xx-MM for keyboard and mouse interface.
		OR
		(2) VKINT-xx-MM for keyboard or mouse interface

M a t e r i a l s N o t S u p p l i e d , B U T M A Y B E R E Q U I R E D :

VKINT-1K-1 Booster Cable for keyboard or mouse interface with Compaq Proliant 2000 and non-Intel

architecture Unix machines with PS/2 ports (such as HP-9000). Two VKINT-1K-1 cables are needed for each applicable computer.

I N S T A L L A T I O N

1.Turn OFF power to all computers that will be connected to the NTI Switch before connecting or disconnecting any cables

WARNING! Y O U M A Y D A M A G E Y O U R C O M P U T E R I F Y O U D O N O T T U R N T H E P O W E R O F F B E F O R E C O N N E C T I N G O R D I S C O N N E C T I N G C A B L E S .

2.Connect PS/2 keyboard to “USER KEYBD” port on rear panel of switch.

3.Connect PS/2 Mouse to “USER MOUSE” port on rear of switch.

4.Connect monitor to “MONITOR” port on rear of switch.

5.Using (1) VVKINT-xx-MM or (2) VKINT-xx-MM or VKEXT-xx-MM cables (required, not supplied), connect keyboard and

mouse ports of PS/2 computer to “CPU-1 KEYBD” and “CPU-1 MOUSE” ports on rear of switch.

N O T E : If installing a Compaq Proliant 2000 or a non-Intel architecture Unix machine with PS/2 ports (such as HP-9000), booster cables may be needed (VKINT - 1K - 1) . If booster cables are used, they must first be directly connected to both the keyboard and mouse CPU ports on the switch.

6.Using VINT-xx - MM or VEXT - xx-MM (required, not supplied), connect video port of PS/2 computer to “CPU-1 VIDEO” port on rear of switch.

7.Repeat steps 5 & 6 for CPU-2.

P O W E R - U P S E Q U E N C E		P O W E R - D O W N S E Q U E N C E
1.	The KEEMUX-P2 is powered by the computers it is connected to.	1. Power down computers.
2.	Turn on power to monitor.

3. Turn on power to either or both computer(s).

U S I N G T H E N T I S W I T C H

The switch can be operated by the front control panel or by keyboard control.

F r o n t P a n e l C o n t r o l

1.Pressing the touch switch on the front panel will toggle between CPU 1 and CPU 2 and connect the selected computer to the keyboard, monitor and mouse.

2.Holding down the "CPU SELECT" button for more than 2 seconds will cause the switch to cycle through 3 extended modes of operation: SCAN, BROADCAST, and COMMAND (see Keyboard Control, Scan and Broadcast sections). Release the button when the desired mode has been selected.

K e y b o a r d C o n t r o l
To control switch from keyboard, “COMMAND” Mode must be enabled.
To enable "COMMAND" Mode:	“CTRL” + “`” (accent key)
To disable "COMMAND" Mode:	“ESC” or “CTRL” + “`”
To increment port:	"I" or à
To decrement port:	"D" or ß
To select a specific port:	“P01” or “P02”
To enable / disable "BROADCAST" Mode:	"B"
To enable / disable "SCAN" Mode:	"S"
To set the scan dwell time (time in seconds before switching to other port):	" Txxx" (xxx from 002 to 255)

*NOTE: You must exit "COMMAND" Mode in order to type to a computer .

3