Sun Microsystems
X6450
manual
Select Array Configuration Utility
Install
Login
Connecting to SAS Devices
3shows the configuration
Accessing the System Console
Using Unix Commands
1Dongle Cable Connectors
6Remote Control Screen
Routine Power On and Power Off
Product Updates
Page 68
FIGURE
B-1
Adaptec RAID Controller Utility (ARCU) Initial View
3.
Select Array Configuration Utility.
The Array Configuration Utility appears.
FIGURE
B-2
Array Configuration Utility View
58
Sun Blade X6450 Server Module Installation Guide • September 2008
Page 67
Page 69
Image 68
Page 67
Page 69
Contents
Sun Blade X6450 Server Module Installation Guide
Please Recycle
Contents
Installing and Configuring the Server Module
Grub
Contents
Index
Using Unix Commands
Preface
Related Documentation
Shell Prompts
Typographic Conventions
Third-Party Web Sites
Product Updates
Documentation, Support, and Training
Sun Welcomes Your Comments
Introduction
Terms and References Used in This Book
Installation Overview
Routine Power On and Power Off
To Apply Standby Power
To Power On Main Power for All Server Components
Insert the server module into a powered chassis
To Shut Down Main Power
1Server Module Front Panel
About Diskless Servers
Compact Flash Drive
Connecting to SAS Devices
Solid State Disk Drive SSD
1SAS Connection Summary
Internal Connection to a Sun Blade 6000 Disk Module
External Connecton to the 10 GbE Ethernet Connections
About the Boot Process
3shows the configuration
Bios and Bios Configuration Utilities
Bootloader
Windows Bootloader
Grub
2BIOS Configuration Utilities
To Configure Netboot or Compact Flash Boot
To Configure the QLogic Fibre Channel in the Bios
Enable the PCIe ExpressModule as a boot device
Save your changes
RAID Configuration
To Load an OS Over the Network Netboot
To Configure the Sun Blade RAID 5 Expansion Module
To Configure the Sun Blade 0/1 RAID Expansion Module
Installing an Operating System
Directing Console Output
Sun Blade X6450 Server Module Installation Guide September
Locate the desired slot in the chassis
Inserting the Server Module
To Insert the Server Module
Remove the filler panel
LED Behavior
Rotate the ejectors down until they snap into place
Accessing and Configuring the Ilom
Displaying the Service Processor’s Ilom IP Address
Connecting to the Ilom
To Display the Service Processor’s Ilom IP Address
Log in to the CMM Ilom CLI Type the command
Type your user name and password
To Connect to the Ilom Web GUI
Type the password when prompted. The default is changeme
To Connect to the Ilom CLI
Click Log
To log on to the ILOM, type $ ssh root@ipaddress
Accessing and Configuring the Elom
To log out, type
Displaying the Service Processor’s Elom IP Address
To Display the Service Processor’s Elom IP Address
Connecting to the Elom
To Connect to the Elom Web GUI
To Connect to the Elom CLI
Type the user name and password
Click Login
To Configure the Service Processor’s Network Configuration
Type the following commands
To log out, type exit
Log in to the CMM Ilom
Accessing the System Console
To Access the System Console Directly
To Access the System Console Using the Ilom CLI
To Access the System Console Using the Elom CLI
To power on the system, type the command
To start the system console, type
To Access the System Console Using the Ilom Web
Type a valid user name and password. For example
6Remote Control Screen
Click the Launch Redirection tab
To Access the System Console Using the Elom Web
Type the default user name and password
Sun Blade X6450 Server Module Installation Guide September
8Selections forBooting the Operating System
Dongle Cable Connections
9Dongle Cable Connections
1Dongle Cable Connectors
Sun Blade X6450 Server Module Installation Guide September
Installation Worksheet
Table A-1Installation Worksheet
Appendix a Installation Worksheet
GMT
P E N D I X B
Introduction to the Bios RAID Configuration Utility
Hot-Plug Addition Conditions
Hot-Unplug and Plug Replacement or Reinsertion Conditions
Hot-Unplug Removal Conditions
Running the Bios RAID Configuration Utility
To Start the Bios RAID Configuration Utility
Using the ACU to Create and Manage Arrays
To Navigate the Bios RAID Configuration Utility
Start the Bios RAID Configuration utility
To Start the ACU
To Create a New Array With the ACU
Select Create Arrays from the main ACU menu
To Make an Array Bootable With the ACU
To Manage Existing Arrays With the ACU
To Initialize Disk Drives With the ACU
Restart the computer
To Rescan Disk Drives With the ACU
To Perform a Secure Erase on Disk Drives With the ACU
To Stop a Secure Erase in Progress With
Select Rescan Drives from the main ACU menu
Using the -Select Utility to Modify REM Settings
To Start Using a -SelectUtility
To Apply Changes and Exit a -SelectUtility
Press Esc until you are prompted to exit
To Modify General Settings With a -SelectUtility
Some options might not be available
To Modify SAS-Specific REM Settings With a Select Utility
Table B-2SAS-Specific REM Settings
To Locate Disk Drives With the Disk Utilities
Using the Disk Utilities to Manage Disk Drives
To Format or Verify a Disk Drive With the Disk Utilities
Select Disk Utilities
Initializing a RAID Array
To Identify Disk Drives With the Disk Utilities
Select Array Configuration Utility
Figure B-1Adaptec RAID Controller Utility Arcu Initial View
When you have selected a drive, press Enter
Select Initialize Drives. a list of drives appears
Select drives to initialize
Type yes
Select Create Array from the main menu
Select the drives to be included in the array
Press Enter or click Done to proceed
After you make your selections, press Enter
Make the following selections
Click Enter to proceed
Figure B-7Write Cache Warning
Index
ACU
Page
Index
Top
Page
Image
Contents
