Patton electronic 2520RC, 2500RC, 2510RC user manual Switch SET S2 Summary Table

Page 6

Switch S1-4: Circuit Assurance

The transmitter and the CTS output can be configured to go On only when a working communication circuit is established. If Circuit Assurance is used, enable it on only one end of the communication link. Circuit Assurance should be enabled in Switched 56 mode.

 

Circuit

 

S1-4

Assurance

Description

On

Enabled

CTS will go low and the transmitter

 

 

will be held off if the receiver is in

 

 

the No Signal state or CD is low

Off

Disabled

The transmitter and CTS will

 

 

operate without regard to the

 

 

receiver state

Switch S1-5: RTS

The RTS input can be forced on, ignoring the terminal’s RTS signal. RTS controls the transmitter by either sending the user’s data or sending an idle code.

S1-5

RTS

Description

Off

Forced On

An On (high) condition is trans-

 

 

mitted regardless of the state of

 

 

this unit’s RTS input

On

Follows DTE

The RTS input controls the

 

 

transmitter

Switch S1-6: Character Length

In asynchronous data format, 10 and 11 bit characters are supported. This setting is ignored in synchronous data format.

 

Character

 

 

Character Description

S1-6

Length

Start

Data bits

Parity

Stop bits

Off

10-bit

1

8

None

1 or more

 

 

1

7

1

1 or more

 

 

1

7

None

2

On

11-bit

1

8

1

1 or more

 

 

1

9

None

1 or more

Switch S1-7: Data Format

The data format selection controls whether an async-to-sync conversion is performed.

S1-7

Data Format

On

Asynchronous

Off

Synchronous

Switch S1-8: DSR System Status

The behavior of the DSR output during performance of a local loop can be controlled.

 

DSR

 

S1-8

Loop Status

Description

On

DSR On

DSR remains high (On) during the

 

 

Analog Loop

Off

DSR Off

DSR goes low (Off) during the

 

 

Analog Loop

3.1.2 Switch Set “S2”

The configuration switches on switch S2 control the Rate Adapter/DTE Rate, Clock Mode, Anti-Stream Timer and RTS/CTS Delay. The table below shows factory default settings for Switch S2. Following the table are descriptions of each switch setting.

SWITCH SET S2 SUMMARY TABLE

Position

Function

Factory Default

Exceptions

 

 

 

 

 

 

 

S2-1

Rate Adapter

Off

} DTE Rate

 

 

S2-2

Rate Adapter

Off

 

 

S2-3

Rate Adapter

Off

 

 

 

 

 

 

 

 

 

 

S2-4

DTE Loop Control

Off

Disabled

 

 

 

 

 

 

 

 

S2-5

Clock Mode

Off

}

Network

Off Model 2510

S2-6

Clock Mode

Off

Clock

On }

Switched 56

 

 

S2-7

Anti-Stream Timer

On Disabled

 

 

 

 

 

 

 

S2-8

RTS/CTS Delay

Off Normal

 

 

 

 

 

 

 

 

 

9

10

Page 5 Page 7
Image 6
Page 5 Page 7
Contents User Manual Radio and TV Interference CE Notice ServiceFCC Information Monday through FridaySupported Applications Product FeaturesGeneral Product Description Model 2500RC Series ApplicationsSwitch SET S1 Summary Table Front Card Configuration Hardware SwitchesSwitch Set S1 Switches S1-1. S1-2 and S1-3 Line RateSwitch SET S2 Summary Table Switches S2-5 and S2-6 Clock Mode Switches S2-1, S2-2 and S2-3 Rate Adapter/DTE RateSwitch S2-4 DTE Loop Control Switch S2-7 Anti-Stream TimerAccessing the Software Control Port Setting Rotary Address SwitchesFront Card Configuration Software Switches Using the Software Menu SystemLine Rate Verifying Software Switch ControlSetting Software Switch Parameters Circuit AssuranceForce RTS Character LengthDTE Data Format Rate Converter/DTE Rate Clock ModeDSR Status During Local Loopback DTE Loop ControlAnti-Streaming Timer RTS/CTS DelayInterface Card Strap Summary Table #1 Rear Card ConfigurationModel 1000RCM12548 Strap Settings DTE Shield Pin 1 & Frgnd JB3Sgnd & Frgnd JB4 Model 1000RCM13448 Strap SettingsRack Power Supply JB4Wiring the Model 2500RC Series Switching the Power Supply On and OffInstalling the Model 2500RC Series Into the Chassis LED DescriptionsDisplaying Configuration Settings Status DisplaysLoopback Test Modes LAL Test ProcedureDisplaying Line/Loop Status Local Analog Loopback LALRemote Digital Loopback RDL RDL Test ProcedureTelco Testing RDL Test ActivationSwitched 56 Dialing Commands Models 2510RC & 2520RC Store Phone Number Enable DTR DialingV.52 BER Test Pattern Generator Specifications Cable Recommendations Wire Gauge Capacitance ResistanceAppendix C Factory Replacement Parts Accessories Patton Model # DescriptionInterface PIN Assignment DDS Interface CONNECTOR, Terminal InterfaceDB-25 CONNECTOR, Terminal Interface Appendix DEXT INT Transmitter Clock Source During Test LoopsINT RC = Received Clock

2510RC, 2500RC, 2520RC specifications

The Patton Electronics 2520RC, 2510RC, and 2500RC are versatile remote access devices designed to facilitate secure and efficient communication for various applications. These models are recognized for their robust performance, scalability, and advanced technology, making them ideal for industries such as telecommunications, information technology, and remote monitoring.

The Patton 2520RC is renowned for its dual Ethernet port functionality, supporting both LAN and WAN connections. This feature ensures seamless data transfer and allows for the integration of multiple devices within a network. The device supports a range of protocols including TCP/IP, allowing for compatibility with various network environments. Robust security features, including VPN options, ensure that data transmissions remain secure and protected against unauthorized access. Additionally, the 2520RC is equipped with advanced monitoring and management capabilities that enable network administrators to keep track of performance metrics in real-time.

Moving to the 2510RC, this device is particularly well-suited for applications requiring voice over IP (VoIP) functionality. It supports a variety of codecs, enabling high-quality voice communication over data networks. The 2510RC also includes features for echo cancellation and noise reduction, ensuring clarity during VoIP calls. Its integration capabilities allow it to work seamlessly with existing telephony systems and provides flexible connectivity options to adapt to different business needs.

The 2500RC is the entry-level model of this series, designed with simplicity and effectiveness in mind. It features one Ethernet port and is particularly suitable for smaller networks or remote locations. Although it has fewer advanced features compared to its siblings, the 2500RC maintains reliability and functionality crucial for basic communication needs. Its compact design makes it easy to deploy in tight spaces, and its ease of installation means that users can be up and running quickly without extensive configuration.

All three models incorporate Patton’s commitment to high-quality manufacturing and customer support. They are built to withstand harsh conditions, ensuring durability for long-term use. Featuring power over Ethernet (PoE) support, these devices can simplify installation by reducing the need for additional power sources.

In summary, the Patton Electronics 2520RC, 2510RC, and 2500RC offer a range of features and technologies designed to meet various remote access and communication needs. Their versatility, combined with robust security measures and easy management tools, make them top choices for businesses looking to enhance their connectivity solutions.
Top Page Image Contents