Patton electronic 4960 manual RedBoot ipaddress -g gateway

Page 35

SmartNode 4960 Getting Started Guide4 • Initial configuration

Step

Command

Purpose

 

 

 

2

RedBoot> ip_address -g gateway

Sets the IP address of the default gateway.

optional

 

 

 

 

 

3

RedBoot> ping -htftp-server_ip_address

Tests the connectivity to the TFTP server.

optional

 

 

 

 

 

4

RedBoot> load -r -v -h host -b

Downloads an application image into the vola-

 

base_address file_name

tile memory (RAM) from where the SmartNode

 

 

could directly execute it.

 

 

host: IP address of the TFTP server

 

 

base_address: memory location where to store

 

 

the application image. Use the default address

 

 

0x1800100

 

 

file_name: path and name of the file on the

 

 

TFTP server. Note: use the image file that con-

 

 

tains the whole application, not the image

 

 

parts.

 

 

 

5

RedBoot> fis delete -n 1

Deletes the first application image.

 

 

Reply with ‘y’ to the confirmation request.

 

 

 

6

RedBoot> fis create

Stores the downloaded application image to

 

 

the permanent memory (flash:).

 

 

Reply with ‘y’ to the confirmation request.

 

 

 

7

RedBoot> fis list -l

Checks whether the image has been success-

 

 

fully stored, whether it is the desired Release

 

 

and Build, and whether it is valid.

 

 

 

8

RedBoot> go

Starts the application image that was down-

 

 

loaded into the volatile memory (RAM).

 

 

 

Note With the Bootloader, only the Ethernet interface 0/0 is available. The Boot- loader applies the IP address, subnet mask, and default gateway that were last configured by the Bootloader itself or by another application (e.g. Smart- Ware). If an application configured the Ethernet interface 0/0 to use DHCP, the Bootloader will also use DHCP to learn the interface configuration. It can receive and apply the IP address, subnet mask, default gateway, and default (TFTP) server (transmitted as basic DHCP information ‘Next server IP address’).

Note This procedure does not download the respective CLI description file.

Download it after starting up SmartWare with the following command:

copy tftp://<tftp_server_address>/<server path>/b1 flash:

Example: Downloading and storing a new application image (SmartWare)

RedBoot> ip -l

172.16.40.98/19

RedBoot> ip -g

172.16.32.1

RedBoot> ping -h

172.16.32.100

Network PING - from 172.16.40.98 to 172.16.32.100

..........PING -

received 10 of 10 expected

RedBoot> load -r

-v -h 172.16.32.100 -b 0x1800100 /Sn4xxx/image.bin

Bootloader

 

35

VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Page 34 Page 36
Image 35
Page 34 Page 36
Contents SmartNode 4960 Series Trademark Statement Summary Table of Contents Table of Contents Table of Contents Cabling List of Figures List of Tables Structure About this guideAudience Safety when working with electricity PrecautionsGeneral conventions Typographical conventions used in this documentGeneral observations Node General information Chapter contentsSmartNode SmartNode 4960 overviewSmartNode 4960 models with integrated G.SHDSL interface SmartNode 4960 rear panel ports are described in table SmartNode 4960 rear panelWAN ETH 0/0 SN4960/4E SmartNode 4960 front panelLED Applications overview Application-Edge intelligence of enterprise communication IntroductionHow it works Application-Multi-service Isdn Internet telephony IADApplications overview SmartNode installation Network information Planning the installationNetwork Diagram Site logInstalling the gateway router Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the power supply Initial configuration Connecting the SmartNode to your laptop PC Connecting the SmartNode to your laptop PCChanging the WAN IP address Factory-default IP settingsLogin Configuring the desired IP addressLAN Connecting the SmartNode to the networkLoading the configuration optional Load a new application image SmartWare via Tftp BootloaderStart Bootloader Start-up with factory configurationRedBoot ipaddress -g gateway Xmodem ymodem -b Load a new application image SmartWare via the serial linkAdditional information Shdsl Basic Configuration Configuring PPPoE Line SetupProfile napt WAN Configuration SummaryUsing PVC channels with PPPoE Setting up permanent virtual circuits PVCUsing PVC channels in bridged Ethernet mode Diagnostics Troubleshooting DSL ConnectionsContacting Patton for assistance Patton support headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceEMC Appendix a Compliance informationFCC Part 68 Acta Statement SafetyCompliance Radio and TV InterferenceCE Declaration of Conformity Industry Canada NoticeAppendix B Specifications Data connectivity Voice processing signalling dependentVoice connectivity Voice routing-session router Voice signallingFax and modem support Physical IP servicesManagement SystemDSL Shdsl Daughter Card if applicableSmartNode Model SysObjectID Identification of the SmartNode devices via SnmpAppendix C Cabling Console Connecting a serial terminalEthernet E1 PRI T1 PRI Appendix D Port pin-outs EIA-561 RJ-45 8-pin port Console portShdsl port PRI portAppendix E SmartNode 4960 factory configuration Introduction Appendix F End user license agreement End User License Agreement Other licenses Termination
Related manuals
Manual 67 pages 50.22 Kb

4960 specifications

The Patton Electronics 4960 is a cutting-edge solution designed to facilitate reliable, high-speed data communication over traditional copper telephone lines. This versatile device is particularly noted for its carrier-grade performance and is widely utilized in a variety of applications, from telecommunications to industrial automation.

One of the main features of the 4960 is its ability to support both T1 and E1 connectivity. This adaptability makes it an excellent choice for organizations that need to interface with different types of line configurations. The device offers a reliable method for transmitting voice and data without significant loss or degradation in quality. Enhanced echo cancellation technology further optimizes communication, ensuring clear transmission even in challenging network conditions.

The 4960 is equipped with advanced modulation techniques, including Adaptive Trellis Coding and Echo Cancellation. These technologies enable the device to maintain high throughput and resilience in fluctuating line conditions. This adaptation to network conditions makes the Patton 4960 well-suited for long-range communications, significantly extending the reach of WAN connections.

In terms of management and monitoring, the device boasts both SNMP support and a web interface that allows for straightforward configuration and real-time monitoring. The user-friendly interface is designed to provide network administrators with the necessary tools to troubleshoot and ensure optimal performance, reducing downtime and maintenance costs.

In addition to its robust architecture, the Patton 4960 integrates seamlessly into various networking environments. It can be deployed in a range of scenarios, such as connecting remote sites, supporting legacy equipment, or even functioning as a bridge for VoIP systems. The flexibility offered by the 4960 enhances its appeal across different sectors, from small businesses to large enterprises.

With built-in surge protection and a durable casing, the Patton 4960 is designed with reliability in mind, ensuring that users can count on consistent performance even in demanding environments. This dedication to robustness contributes to its reputation as a trusted device among IT professionals.

In summary, the Patton Electronics 4960 stands out for its combination of advanced features, compatibility, and ease of use. Its adaptability to both T1 and E1 lines, coupled with robust data transmission technologies, makes it a valuable asset for any organization seeking reliable communication solutions.
Top Page Image Contents