TP-Link manual TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide

Page 17

4.You have now successfully connected to your network. Click Close to enjoy the Internet.

TL-WN881ND300Mbps Wireless N PCI Express Adapter User Guide

Input the password which can be found on the configuration page of your router or access point, then click OK to continue. Or push the QSS/WPS button on your router if your router features the QSS/WPS function to quickly build a connection without having to enter a key.

Figure 3-4

4.You have now successfully connected to your network. Click Close to enjoy the Internet.

Figure 3-5

5.To view more information about the network currently connected, click Status in the tools section and the page will display information such as the network type, link quality and wireless mode.

11

Image 17

Contents Rev TL-WN881ND 300Mbps Wireless N PCI Express AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTNational Restrictions CE Mark Warning2400.0-2483.5 MHz CountryProduct Description 300Mbps Wireless N PCI Express Adapter DECLARATION OF CONFORMITYETSI EN 300 328 V1.7.1 ETSI EN 301 489-1 V1.8.12008 & ETSI EN 301 489-17 EN60950-12006CONTENTS Conventions Package ContentsChapter 1 Introduction 1.2 Features1.1 Product Overview TL-WN881ND 300Mbps Wireless N PCI Express Adapter User GuideStatus 1.3 Hardware OverviewWorking Status Flashing Quickly2.2 Software Installation Chapter 2 Installation2.1 Hardware Installation TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide5. Click Install to continue the setup 6. The utility and drivers will install. This may take 1~2 minutes TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 3.1 To connect using TWCU Chapter 3 Connect to a Wireless Network3. If word None appears behind the SSID, this means the network to be connected is not security-enabled and you can connect to the network without entering a key. To prevent outside intrusion and safeguard your network, it is strongly recommended to set a password to your router or access point 4. You have now successfully connected to your network. Click Close to enjoy the Internet 3.2.1 PBC Push Button Configuration method 3.2 To connect using QSS3. The adapter will be connecting to the target network 3.2.2 PIN method 2. The adapter will be connecting to the target network TL-WN881ND 300Mbps Wireless N PCI Express Adapter User Guide 3.3.1 In Windows 3.3 To connect using Windows built-in wireless utility3.3.2 In Windows Vista 2. The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect 3.3.3 In Windows XP Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-25 appears to continue 3. The utility will display any available wireless networks in your area. Click on a network displayed using the SSID and click the Connect button 4.1 Profile Chapter 4 ManagementThe following items can be found on the screen 4.1.3 Delete a profile 4.1.2 Modify a profile4.2 Advanced 4.3 About Chapter 5 AP Mode ¾ SoftAP mode Select to enable or disable the function 6.1 Uninstall the utility software from your PC Chapter 6 Uninstall Software6.2 Uninstall the driver software from your PC Environmental and Physical Appendix A SpecificationsNormal Appendix B Glossary ¾ Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS