TP-Link manual Quick Installation Guide, TL-WR642G 108M Wireless Router User Guide

Page 13
4.2 Quick Installation Guide

TL-WR642G108M Wireless Router User Guide

If the result displayed is similar to that shown in figure 4-1, the connection between your PC and the router has been established.

Figure 4-2: Failed result of Ping command

If the result displayed is similar to that shown in figure 4-2, it means that your PC has not connected to the router. Please check it following these steps:

1.Is the connection between your PC and the router correct?

Note: The Link/Act LEDs of LAN port on the router and LEDs on your PC's adapter should be lit.

2.Is the TCP/IP configuration for your PC correct?

Note: If the router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1

4.2 Quick Installation Guide

With a Web-based (Internet Explorer or Netscape® Navigator) utility, the TL-WR541G 54Mbps Wireless Router is easy to configure and manage. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a web browser.

Connect to the router by typing http://192.168.1.1 in the address field of web browser.

Figure 4-3 Login to the router

After a moment, a login window will appear similar to that shown in Figure 4-4. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.

- 9 -

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page COPYRIGHT & TRADEMARKS 5.4.1 LAN 5.8.5 Remote Management TL-WR642G 108M Wireless Router User Guide Package contents1.1 Purposes Chapter 1 About this Guide1.2 Conventions 1.3 Overview of this User GuideChapter 2 Introduction 2.2 Features2.1 Overview of the Router 2.3.1 The Front Panel 2.3 Panel LayoutWireless antenna Factory Default Reset button 2.3.2 The Rear PanelThere are two ways to reset the routers factory defaults Figure 2-2 Rear Panel sketch3.2 Installation Environment Requirements Chapter 3 Connecting the Router3.3 Connecting the Router 3.1 System RequirementsSwitch/Hub 108M Wireless Router User GuideTL-WR642G （XDSL 、Cable 、Ethernet ）4.1 TCP/IP configuration Chapter 4 Quick Installation Guide4.2 Quick Installation Guide Figure 4-4 Login Windows Figure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters 5.1 login Chapter 5 Configuring the Router2. Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP addressPlease refer to Section 4.2 Quick Installation Guide 5.3 Quick Setup5.4 Network 5.4.2 WAN 5.4.1 LANFigure 5-4 WAN - Dynamic IP Figure 5-4a WAN - 802.1X + Dynamic IP Figure 5-5a WAN - 802.1X + Static IP Connect Manually - You can configure the router to make it connect or disconnect manually. After a specified period of inactivity Max Idle Time, the router will disconnect your Internet connection, and not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested 5.4.3 MAC Clone 5.5.1 Wireless Settings 5.5 WirelessMode - Select the desired wireless mode. The options are 5.5.2 MAC Filtering Figure 5-11 Wireless MAC address Filtering 6. Click the Save button to save this entry 5.5.3 Wireless Statistics 5.6 DHCP 5.6.1 DHCP Settings5.6.3 Address Reservation 5.6.2 DHCP Clients ListTo modify A Reserved IP address To Reserve IP addressesTo delete all Reserved IP addresses 5.7.1 Virtual Servers 5.7 ForwardingTo delete a service entry To setup a virtual server entryTo delete all service entries To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows Deleting an existing rule Modifying an existing ruleTo delete all rules 5.7.3 DMZ5.7.4 UPnP 5.8.1 Firewall 5.8 Security5.8.2 IP Address Filtering 5.8.3 Domain Filtering TL-WR642G 108M Wireless Router User Guide 5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Enable ICMP-FLOOD Attack Filtering - Enable or Disable the ICMP-FLOOD To add static routing entries 5.9 Static RoutingTo modify an existing entry 1. Modify the entry’s Destination IP Address, Subnet Mask and GatewayTo delete all the entries 5.10 DDNS5.10.1 Oray.net DDNS 5.10.2 Comexe.cn DDNS 5.11 System Tools5.11.2 Firmware 5.11.1 Time5.11.3 Factory Defaults 5.11.5 Password 5.11.4 Reboot5.11.7 Statistics 5.11.6 LogStatistics Table 1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 1. Install TCP/IP component Appendix B Configuring the PCs2. Configure TCP/IP for your computer Assigned by DHCP Sever Setting IP address manually Figure B-7 IP Address tab click Add button. Shown below Figure B-9 DNS Configuration tab TL-WR642G Appendix C SpecificationsGeneral Environmental and PhysicalAppendix D Glossary Domain Name - A descriptive name for an address or group of addresses on the Internet E-mail support@tp-link.com Appendix E Contact Information
Related manuals
Manual 85 pages 25.82 Kb

TL-WR642G specifications

The TP-Link TL-WR642G is a wireless router that was designed to meet the growing demands for reliable home networking solutions. Known for its balance of performance and affordability, this router has become a go-to choice for many households and small offices looking for efficient internet connectivity.

One of the main features of the TL-WR642G is its adherence to the 802.11g wireless standard, which provides a theoretical maximum data transfer rate of up to 54Mbps. This makes it suitable for various applications, including web browsing, streaming media, and online gaming. It operates in the 2.4 GHz frequency band, which is widely supported by a multitude of devices, ensuring compatibility and convenience for users.

The TL-WR642G comes equipped with a built-in NAT (Network Address Translation) router that allows multiple devices to share a single internet connection without compromising speed or performance. By using this feature, users can connect various devices – from laptops to smartphones and smart TVs – without the need for additional networking hardware. The router also includes a 4-port 10/100Mbps LAN switch, giving users the flexibility to connect wired devices directly for faster and more stable internet access.

In terms of security, the TP-Link TL-WR642G supports various encryption methods such as WEP, WPA, and WPA2, ensuring that your wireless network remains secure from unauthorized access. This is especially important in today’s digital age, where online security threats are prevalent.

Another notable characteristic is the easy setup and management interface provided by TP-Link. The TL-WR642G features a web-based management platform that allows users to configure network settings with minimal effort. This user-friendly interface caters to both novice users and network professionals, making it accessible to all.

Furthermore, the router is equipped with a variety of advanced management features, such as IP and MAC address filtering, parental controls, and network traffic statistics. This allows users to control access to the network while monitoring usage patterns for better management.

In conclusion, the TP-Link TL-WR642G stands out as a reliable and user-friendly router, with its solid performance, essential security features, and easy-to-manage interface. It offers a practical solution for anyone looking to enhance their home or small office network with dependable wireless connectivity.
Top Page Image Contents