Kramer Electronics VP-128H user manual Your RC-1616 Remote Control

Page 14

Your RC-1616 Remote Control

6 Your RC-1616 Remote Control

The RC-1616Remote Control1 can be used:

￿￿With the front panel and rear panel intact, see section 6￿ .1

￿￿With the RC-1616front panel detached, see section 6￿ .2

6.1The RC-1616 with the Front Panel and the Rear Panel Intact

Figure 7, Table 6 and Table 7 define the front and rear panels of the RC-1616:

Figure 7: RC-1616 Remote Control

Table 6: RC-1616 Remote Control Front Panel Features

#

Feature

Function

1

Slide Action Latches

Fasten the front panel into the frame

2

VIDEO2 Button

Affects video (audio does not switch)

3

AUDIO2 Button

Affects audio (video does not switch)

4

VOLUME Up3 Button

Pressing together with an IN / OUT Selector button decreases the level

5

VOLUME Down3 Button

Pressing together with an IN / OUT Selector button increases the level

6

IN Buttons

Select the VGA/XGA input to switch to the VGA/XGA output (from 1 to 16)

7

OUT Buttons

Select the VGA/XGA output4 to which the VGA/XGA input is switched

 

 

(from 1 to 16)

1 It is fully enclosed on all sides, 2 inches deep, and includes a small processor board that performs the button functions and provides the 10 Base T network interface

2 When the panel is powered ON, this button is OFF. Pressing this button will cause that button to latch ON. Pressing the same button again will turn off this button. If either button is in the ON mode, pressing the other button will turn OFF the first button (both buttons on, is an invalid condition). If both buttons are pressed at the same time, both buttons turn OFF (“AFV”) and then re-selecting the desired button is required to turn ON that mode. When the video and audio sources are different, the audio input lamp flashes on and off to indicate “breakaway”

3 The VOL UP button takes precedence over the VOL DOWN button if both are pressed. The VOL UP and VOL DOWN buttons illuminate when pressed, but do not cause the Input Selector or Output Selector buttons to illuminate

4 Each output can be muted independently; and can be set to a delayed switch through black, with a user selectable delay increment for each output

11

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Models Contents Figures TablesIntroduction Getting StartedOverview About the VP-128HAchieving the Best Performance Your VP-128H Matrix SwitcherAbout the RC-1616 VP-128H with the Front Panel and the Rear Panel IntactVP-128H Matrix Switcher VP-128H Matrix Switcher Front Panel Features VP-128H Without the Front Panel but with the Rear PanelVP-128H Local Control Panel Detached Front Panel VP-128H Local Control Panel1Connecting a VP-128H Matrix Switcher Connecting the VP-128H Matrix SwitcherControlling via RS-232 for example, using a PC Connecting a PC without using a Null-modem AdapterRJ-45 Pinout Crossover Cable RJ-45 Pinout Connecting a VP-128H Matrix Switcher Your RC-1616 Remote Control RC-1616 with the Front Panel and the Rear Panel IntactRC-1616 Front Panel Detached Define the RC-1616with its front panel detached2Setting the Dipswitches Connecting a RC-1616 Remote Control Operating the VP-128H Matrix Switcher Switching OUT-IN CombinationsTechnical Specifications Includes the technical specificationsCommunication Protocols Kramer 2000 Protocol Supported Subset3rd Byte 1st Byte2nd Byte 4th ByteSwitch Video Switch Video Crosspoint Parameter TerminologyRequest Audio Output Status Switch Audio Switch Audio CrosspointRequest Video Output Status Setup Recall Setup Save Store / Delete Video StatusSave Delete Bi-Directional command example Breakaway Setting Audio follows videoError Request Breakaway SettingError Response Error Invalid Instruction Out of Range Machine Busy ExampleSet Audio Parameter Store Audio StatusRecall Audio Status Value Request Audio ParameterIncrease / Decrease Audio Parameter Set Auto-Save Audio Parameter SettingsInput Bits Save BitsLoad Audio Data Take Cancel ExampleLoad Video Data Define Machine CommandNumber of inputs Number of outputs Number of setups For video For audioSierra Video Systems1 SVS RS-232 Compatible Protocol Generic ProtocolOK!!CR Clear Clear MatrixConfig Configure Matrix Request **CONFIG1234 , oo , ii , l , f1 , f2Request **CHANGE HEX Crosspoints restored from memory Crosspoint restore failedChange Change protocol X8,3,2,3,4 Delay Vertical Sync IntervalsConnect Crosspoint Setup a Salvo Connect Sequence X1,5,0 D200 D100 X1,6,0 SCommand Audio Gain Control Trigger a Salvo Connect SequenceRequest **S Command RGB Mute delayStatus Inquiry for Crosspoints Request **SA Level 1 input number comma Level 8 input number- comma CRSA Status Inquiry for Audio gains X5? ? Query commandAutomatic Output Change Reporting On/Off X5,4,1?Response **E1!!CR Error messages from the router to the host commandPA? Generic Protocol Supported Subset Reconfig Router Manual Reconfiguration IndicatorRGB Delay Global Setups Request setup Audio Input Gain and Attenuation Request input*gainGControls muting and un-muting video outputs. Examples Video Mute Commands Request output*1BAudio Mute Commands Request output*1Z Create Ties View Ties, Gain, Mutes, and Setups V4GOnly the first purchase customer may enforce this warranty 2900-000024 REV

VP-128H specifications

Kramer Electronics VP-128H is an advanced video processor designed to meet the demands of professional AV applications. It excels in delivering high-quality video and audio signals with versatility and efficiency. The VP-128H is particularly ideal for locations that require multi-screen setups such as control rooms, corporate presentations, and large venues.

One of the standout features of the VP-128H is its ability to handle video resolution up to 4K at 60Hz. This ensures that users can enjoy crisp and clear imagery, making it suitable for high-resolution content and detailed visuals. The unit supports a wide range of video formats including HDMI, which allows for seamless integration with modern audio-visual systems.

The VP-128H utilizes advanced scaling technology that upscales lower-resolution sources to match the output display’s resolution. This feature is especially beneficial in environments where various source materials are used, ensuring that the visual quality remains consistent and impressive across all platforms. Additionally, the processor incorporates a powerful video processing engine, enabling real-time control of various video parameters such as brightness, contrast, and color correction.

Flexibility is another key characteristic of the VP-128H. It boasts multiple input options, allowing users to connect multiple sources without hassle. The intuitive layout makes it easy to switch between sources and manage outputs effectively. The device also supports video wall configurations, which is essential for creating stunning display environments where multiple screens are seamlessly synced.

In terms of connectivity, the VP-128H offers both HDMI and HDBaseT options, ensuring that users can effectively transmit high-definition content over long distances without signal degradation. The HDBaseT technology is particularly noteworthy as it allows for the extension of 4K video, audio, Ethernet, and control signals over a single CAT5e/6 cable, providing a streamlined installation process.

The user-friendly design includes an intuitive web-based interface, making it straightforward to configure settings and monitor performance remotely. This is a significant advantage for system integrators and operators who require quick adjustments without the hassle of navigating through complex menus.

With robust build quality and reliability, Kramer Electronics VP-128H is designed to withstand the demands of high-usage environments. It’s a versatile solution suitable for a range of professional applications, ensuring that users achieve optimal audio-visual performance consistently. Whether in corporate settings, educational institutions, or events, the VP-128H delivers exceptional quality and flexibility.
Top Page Image Contents