Elo TouchSystems 192XL-XXWA-1 Series Installing the Serial Touch Driver for MS-DOS and Windows

Page 27

Installing the Serial Touch Driver for MS-DOS and Windows 3.1

You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS.

To install Windows 3.x and MS-DOS from Windows 95/98, follow the directions below:

1Insert the Elo CD-ROM in your computer’s CD-ROM drive.

2From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your CD-ROM drive may be mapped to a different drive letter).

3Type install and press Enter to start the installation.

4Align the touchscreen.

You must have already completed Steps 1 and 2 before proceeding. Refer to Chapter 2 of the Elo DOS and Windows Driver Guide as necessary for additional installation information.

To run the INSTALL program:

1Type INSTALL at the DOS prompt in the directory containing the driver install files.

2INSTALL asks you to select the software to install. Then choose d:\EloDos_W31 from the displayed list.

3INSTALL also asks you for the paths to use during installation, or you may use its defaults. INSTALL creates directories as necessary, and warns you if they exist.

If you are updating your software, you may wish to specify the paths containing the earlier versions, and overwrite the obsolete files. All executable programs are upward compatible. For a list of differences from each previous version of the drivers, be sure to select “Differences from Previous Versions” during the installation process.

INSTALL updates your AUTOEXEC.BAT file with the drivers you select. INSTALL makes a copy of your original AUTOEXEC.BAT file, called AUTOEXEC.OLD. If you already have Elo driver commands in your AUTOEXEC.BAT file, they will be commented out.

When INSTALL is finished, it leaves a file called GO.BAT in the subdirectory you specified. GO loads the touchscreen driver, runs the calibration program ELOCALIB, and gives you some final instructions.

If you are using Windows 3.1, you will also calibrate the touchscreen within Windows 3.1 with the Touchscreen Control Panel.

Elo Entuitive Touchmonitor User Guide

27

Image 27
Contents Elo Entuitive Touchmonitor User Guide Elo Entuitive Touchmonitor User Guide Iii Table of Contents Troubleshooting Elo Entuitive Touchmonitor User Guide Introduction Elo Entuitive Touchmonitor User Guide Unpacking Your Touchmonitor Installation and SetupSpeaker cable Product Overview Side View Elo Entuitive Touchmonitor User Guide Touchmonitor and Cables Touch Interface ConnectionRouting the Cables Connecting the Video Cables Connecting the Serial or USB Touchscreen Cable Connecting the Speaker Cable Elo Entuitive Touchmonitor User Guide Tilt Lock Function Optimizing the LCD DisplayStand and Display Separation Vesa Mount on Your TouchmonitorRear Mount Template Front Mount Template Front Mount for Horizontal Surface Mounting the Base Kensington Cable Lock SecurityInstalling the Driver Software If the AutoStart feature is not active Click Start Run Installing the Serial Touch Driver for MS-DOS and Windows Installing the USB Touch Driver Operation Using the On-Screen Display OSD MenusControl Function Side Bezel ButtonsOSD Menu Function Analog VGA Only Brightness Auto AdjustBrightness OSD Language OSD Menu Function DVI-I OnlyTroubleshooting Elo Entuitive Touchmonitor User Guide Native Resolution VGA Touchmonitor Safety Care and Handling of Your Touchmonitor Compatible Video Modes Technical Specifications1280x960 Touchmonitor Specifications Elo Entuitive Touchmonitor User Guide Elo Entuitive Touchmonitor User Guide 19 « LCD Touchmonitor ET192XL-XXWA-1 Dimensions Elo Entuitive Touchmonitor User Guide Aft tilt 90˚ from vertical II. Emissions and Immunity Information Electrical Safety InformationElo Entuitive Touchmonitor User Guide Warranty Elo Entuitive Touchmonitor User Guide