Dukane 8766 manual Projecting AN Image Basic Operation, Turning on the Projector

Page 17

PROJECTING AN IMAGE (BASIC OPERATION)

This section describes how to turn on the projector and to project a 2. Press the ENTER button to execute the selection. picture onto the screen.

Turning on the Projector

NOTE:

•The projector has two power switches: main power switch and POWER button (POWER ON and OFF on the remote control)

•When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off[O] position. Failure to do so may cause damage to the projector.

To turn on the main power to the projector, press the Main Power switch to the ON position ( I ).

Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed.

Only after you press the ON/STAND BY button on the projector cabinet or POWER ON button on the remote control for a minimum of 2 sec- onds will the power indicator turn to green and the projector become ready to use.

After this has been done, you can proceed to the menu operation.

If you want, you can select the menu language later. See "Language" on page E-27.

NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.

When the Lamp mode is set to Eco, the Lamp indicator will light green. If one of the following things happens, the projector will not turn on.

*If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down.

*When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.

*If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on the power.

Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup screen. This screen gives you the opportunity to select one of the seven menu lan- guages: English, German, French, Italian, Spanish, Swedish and Japa- nese.

To select a menu language, follow these steps:

1.Use the SELECT G or H button to select one of the seven languages for the menu.

E-17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model Safety Cautions Whats in the Box? Fire and Shock PrecautionsLamp Replacement Table of Contents Introduction Features youll enjoyIntroduction to the Projector Congratulations on Your Purchase of The ProjectorAttaching the supplied carrying handle Part Names of the ProjectorAttaching the lens cap Top Features Terminal Panel Features Part Names of the Remote Control 7m/22 feet Battery InstallationSelecting a Location Installation and ConnectionsSetting Up the Screen and the Projector Do not attempt to install the projector yourself Distance ChartThrow Distance and Screen Size Reflecting the ImageMaking Connections Connecting Your PC or Macintosh ComputerTo connect Scart output RGB Connecting an External MonitorComponent Connecting Your DVD PlayerConnecting the Supplied Power Cable Connecting Your VCR or Laser Disc PlayerTurning on the Projector Projecting AN Image Basic OperationUsing the Remote Control Adjusting the Picture Size and PositionAdjust the Tilt Foot Selecting a SourceAuto Keystone Correction Correcting the Vertical Keystone DistortionManual Keystone Correction FocusTo turn off the projector Turning Up or Down VolumeAdjusting the Image Using Auto Adjust Using the Remote Mouse Function Convenient FeaturesFreezing a Picture Turning Off the Image and SoundEnlarging and Moving a Picture Getting the InformationBasic Menu Operation Using ON-SCREEN MenuUsing the Menus Clear Lamp Hour Meter List of Menu ItemsControl Panel Key Lock Menu Elements Image Menu Descriptions & FunctionsPicture Advanced SetupEnabling Auto Adjust Auto Adjust Selecting Signal Format Signal SelectAdjusting Position/Clock when Auto Adjust is off InformationDefault To replace the lamp MaintenanceReplacing the Lamp Cleaning or Replacing the Filter CleaningCleaning the Cabinet and the Lens Vacuum the filter-through the filter coverPower Indicator TroubleshootingStatus Indicator Lamp IndicatorImage isn’t square to Common Problems & Solutions Check These ItemsModel Number 8766 Optical SpecificationsPin Assignments of D-Sub RGB Input Connector Cabinet DimensionsMini D-Sub 15 Pin Connector Pin No RGB Signal Analog YCbCr SignalCompatible Input Signal List Dukane Corporation 584-5156 676-2486676-2487 584-0984

8766 specifications

The Dukane 8766 is a state-of-the-art ultrasonic welding system designed for various applications across multiple industries, including automotive, medical, and consumer goods. Known for its reliability and efficiency, the 8766 is particularly well-suited for joining thermoplastic materials through high-frequency vibrations, ensuring strong and consistent welds.

One of the main features of the Dukane 8766 is its advanced ultrasonic technology, which utilizes piezoelectric transducers to convert electrical energy into high-frequency mechanical vibrations. This conversion occurs at a frequency of 20 kHz to 40 kHz, depending on the specific requirements of the application. The system's ability to produce these high-frequency vibrations allows for precise and efficient welding, resulting in minimal thermal impact on surrounding materials.

Another notable characteristic of the Dukane 8766 is its robust digital control system. This system allows for real-time monitoring and adjustment of welding parameters, providing operators with the ability to optimize process settings for specific materials and applications. The user-friendly interface facilitates easy programming, ensuring that both experienced and novice operators can achieve high-quality welds consistently.

The Dukane 8766 is equipped with various technologies aimed at enhancing its performance and versatility. One such innovation is the use of auto-tuning technology, which automatically adjusts the ultrasonic frequency to optimize the welding process based on material characteristics and environmental factors. This feature not only improves efficiency but also minimizes the possibility of weld defects.

Safety and durability are paramount in the design of the 8766. The system includes a powerful cooling mechanism that prevents overheating during prolonged use, ensuring long-term reliability. Additionally, the rugged construction of the machine allows it to withstand the rigors of industrial environments while maintaining precise operational standards.

The compact design of the Dukane 8766 maximizes workspace efficiency, making it suitable for both large-scale production lines and smaller-scale operations. Its flexibility allows for easy integration into existing manufacturing processes, providing a seamless transition for companies looking to upgrade their welding capabilities.

In conclusion, the Dukane 8766 ultrasonic welding system stands out due to its advanced features, including high-frequency vibration technology, automated process control, and robust design. These characteristics make it an ideal choice for businesses seeking reliable and efficient welding solutions across diverse applications.
Top Page Image Contents