Guiding Signals
Projector |
| Control Buttons |
| Indicator | |
Description |
|
|
| ||
| TEMP |
| |||
Status | Power | LAMP (Amber) | |||
| |||||
|
| (Amber) | |||
|
|
|
| ||
|
|
|
|
| |
Standby mode | Projector in Standby mode. Ready to power | BLUE | OFF | OFF | |
| on. | Flashing | |||
|
|
| |||
|
|
|
|
| |
Warming up | Projector takes some time to warm up and | BLUE | OFF | OFF | |
mode | power on. | ||||
|
|
| |||
|
|
|
|
| |
Lamp on | Projector in Normal mode, ready to display |
|
|
| |
| an image. | BLUE | OFF | OFF | |
| Note: The OSD menu is not accessed. |
|
|
| |
|
|
|
|
| |
Cooling mode | Projector is cooling to shutdown. | BLUE | OFF | OFF | |
|
|
|
|
| |
Power Saving | Power Saving mode has been activated. The |
|
|
| |
mode | projector will automatically enter standby | AMBER | OFF | OFF | |
| mode, if an input signal is not detected in | Flashing | |||
|
|
| |||
| two hours. |
|
|
| |
|
|
|
|
| |
Cooling before | The projector takes 60 seconds to cool down |
|
|
| |
Power Saving | before entering Power Saving mode. | AMBER | OFF | OFF | |
mode |
|
|
|
| |
|
|
|
|
| |
Projector | Air vents might be blocked or ambient |
|
|
| |
overheated | temperature may be above 35ºC. The |
|
|
| |
| projector automatically shuts down. Ensure |
|
|
| |
| that the air vents are not blocked and that | OFF | AMBER | OFF | |
| the ambient temperature is within |
|
|
| |
| operational range. If the problem persists, |
|
|
| |
| contact Dell. |
|
|
| |
|
|
|
|
| |
Lamp driver | The lamp driver is overheated. The air vents |
|
|
| |
overheated | may be blocked. The projector automatically |
|
|
| |
| shuts down. Turn the display on again after | AMBER | AMBER | OFF | |
| the projector cools down. If the problem |
|
|
| |
| persists, contact Dell. |
|
|
| |
|
|
|
|
| |
Fan breakdown | One of the fans has failed. The projector |
| AMBER |
| |
| automatically shuts down. If the problem | ÒFF | OFF | ||
| Flashing | ||||
| persists, contact Dell. |
|
| ||
|
|
|
| ||
|
|
|
|
| |
Lamp driver | The lamp driver has failed. The projector |
|
|
| |
breakdown | automatically shuts down. Unplug the power | AMBER |
| AMBER | |
| cord after three minutes then turn the | OFF | |||
| Flashing | Flashing | |||
| display on again. If this problem persists, |
| |||
|
|
|
| ||
| contact Dell. |
|
|
| |
|
|
|
|
| |
Color Wheel | Color wheel cannot start. The projector has |
|
|
| |
breakdown | failed and the projector automatically shuts |
| AMBER | AMBER | |
| down. Unplug the power cord after three | BLUE | |||
| Flashing | Flashing | |||
| minutes and then turn on the projector. If |
| |||
|
|
|
| ||
| this problem persists, contact Dell. |
|
|
|
Fault - DC | Power supply has been interrupted. The |
supply (+12V) | projector automatically shuts down. Unplug |
| the power cord after three minutes and then |
| turn on the projector. If this problem |
| persists, contact Dell. |
AMBER AMBER AMBER Flashing
46