Compaq 300 manual Operation Windows NT

Page 36

Operation (Windows NT)

5.Click on the arrows in the Desktop Area to change the screen resolution.

6.To change the refresh rate, choose one of the options in Refresh Frequency. (You can also change the resolution and refresh rate by choosing List All Modes and the desired mode, and then choosing OK.) If the refresh rate selected is not supported by the resolution you chose, the resolution will automatically change to the nearest value supported by that refresh rate, or the refresh rate will change to support the resolution.

7.Choose Test to verify that the settings work correctly. A test pattern will be displayed on your monitor for about 5 seconds. You will then see the question, "Did you see the test bitmap properly?"

8.If you are satisfied with the video display, choose Yes. Choose OK to change the settings.

9.You may have to adjust your monitor to align the new resolution to the monitor. This is typically done by using the controls on the front or side of the monitor.

__________________________ Note ____________________________

If you accidentally click OK for a resolution that your monitor can’t support on the Windows NT operating system, you may not be able see the display or navigate the controls to fix the problem. If this happens, you can force the workstation to come up in VGA mode.

Windows NT Alpha Platform

Reboot the workstation. During Startup, press F2 to enter setup. Select Utilities and OS Selection Setup. Add the word BASEVIDEO to the OS Options. Complete the boot. The screen is now running in VGA mode. Change the resolution to something you know that the monitor can handle, for example 800x600x60. Reboot again, but this time enter Setup and remove the BASEVIDEO option, or the workstation will come up in VGA mode again. Complete the boot and change the settings to the desired resolution.

Windows NT Intel Platform

Reboot the workstation. During Startup, select Windows NT Workstation 4.0 [VGA Mode]. The screen is now running in VGA mode. Complete the boot and change the resolution to something you know that the monitor can handle, for example 800x600x60. Reboot again, but this time select Windows NT Workstation 4.0. Complete the boot and change the settings to the desired resolution.

___________________________________________________________

5–2PowerStorm 300 AGP and 300/350 PCI Graphics Controllers

Image 36

Contents July Compaq Computer Corporation Houston, TexasJuly Table of Contents Installation Compaq Tru64 Unix Operation Windows NTOperation Compaq Tru64 Unix TablesPage Preface Purpose of This GuideWho Should Use This Guide Structure of This GuideRelated Documentation Conventions Used in This GuideReader’s Comments Getting HelpCompaq Technical Support Compaq WebsiteCompaq Authorized Reseller PowerStorm 300 AGP Graphics Controller Overview PowerStorm 300 AGP Graphics Controller Part NumberIntroduction DescriptionCompaq PowerStorm 300 AGP Software Support Minimum System WorkstationVersion PowerStorm 300 AGP Graphics Controller NLX Connector Pinout Pin No. SignalSpecifications PowerStorm 300 AGP Graphics Controller SpecificationsPage PowerStorm 300 PCI Graphics Controller Overview PowerStorm 300 PCI Graphics Controller Part NumbersDigital Part Compaq Part Description Number Compaq PowerStorm 300 PCI Software Support PowerStorm 300 PCI Graphics ControllerConnector Pinout PowerStorm 300 PCI Graphics Controller Specifications PCIPowerStorm 350 PCI Graphics Controller Overview PowerStorm 350 PCI Graphics ControllerCompaq PowerStorm 350 PCI Software Support Minimum System Workstation ROM Revision VersionConnector Pinouts Stereo Connector Pinouts PowerStorm 350 PCI Graphics Controller Specifications Page Installation Windows NT UnpackingHardware Installation Changing the Bulkhead Bracket, PowerStorm 300 AGP OnlyInstallation of the Graphics Controller Software Installation Microsoft Windows NT Software InstallationPowerStorm 300/350 Software Components PowerStorm 300/350 Software Components on the CDPowerStorm 300 AGP and 300/350 PCI Graphics Controllers Installing/Upgrading PowerStorm Software Display Drivers No Changes The above list matches my computer OpenGL Acceleration Stereo Capability PowerStorm 350 PCI Only Choose the REALimage tm Settings tabAfter Installation Changing the Screen Resolution and Refresh RateOperation Windows NT Operation Windows NT Resolution Vertical Refresh rates Managing Buffer SwapUsing the Display Applet Identifying the Display Driver VersionUsing OpenGL Using OpenGL ApplicationsDeveloping OpenGL Applications on Intel Platforms Pixel Format Support Pixel Format RgbaPerformance Considerations Texture MappingDeveloping OpenGL Applications on Alpha Platforms Overlay PlanesStencil Planes SoftImage Customizations10PowerStorm 300 AGP and 300/350 PCI Graphics Controllers Operation Windows NT 12PowerStorm 300 AGP and 300/350 PCI Graphics Controllers Operation Windows NT 14PowerStorm 300 AGP and 300/350 PCI Graphics Controllers Operation Windows NT Alpha Buffers ∙ Storing alpha values so that they can be read later∙ Blending, using a destination alpha value 18PowerStorm 300 AGP and 300/350 PCI Graphics Controllers Installation Compaq Tru64 Unix Installation Compaq Tru64 Unix Installation Preparation and Information Required LicensePrerequisite Software Installing PowerStorm Display Drivers Booting Compaq Tru64 UnixAlternate Console Copying the Kit from CD-ROMInstalling the Kit Unpacking the Kit6PowerStorm 300 AGP and 300/350 PCI Graphics Controllers Indicate whether you wish to modify the configuration file Configuration Recommendations Tuning Techniques# sysconfig -qsubsystemname Page Operation Compaq Tru64 Unix Synchronizing Buffer Swaps Operation Compaq Tru64 UnixDefault OpenGL Texel Size Identifying the Driver Version OpenGL Visual Support Indirect Contexts, GLXPixmaps, and the Software Renderer Developing OpenGL Applications on Tru64 Unix Visual ID0x21 0x22 0x23 0x24 Performance and Functionality Considerations 0x2d0x2f ∙ Blending using a destination alpha value Stencil Planes