Christie Digital Systems 38-VIV403-01 user manual Basic Operation, Turning on / OFF Projector

Page 22
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When Power Management function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on pages 40 and 41.
When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.
When both WARNING TEMP. and READY indicators to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF.
2. Turn a projector on again.
When WARNING TEMP. indicator continues to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 44.)
4. Turn a projector on again.
If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING TO

 

PROJECTOR" on Pages 12~15 for connecting that equipment.)

2

Connect a projector's AC Power Cord into a wall outlet and turn

MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,

 

and READY indicator lights GREEN.

3

Press POWER ON-OFF button on Side Control or on Remote

Control Unit to ON. LAMP indicator dims, and Cooling Fans start

to operate. Preparation Display appears on a screen and count- down starts. Signal from source appears after 30 seconds. Current Input position and Lamp status are also displayed on screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on page 45.)

LAMP STATUS

INPUT 1

13

24

30

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Side Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

2

Press POWER ON-OFF button again to turn off projector. LAMP

indicator lights bright and READY indicator turns off. After

approximate 90 seconds, READY indicator will light green again and projector may be turned on by pressing POWER ON-OFF button.

Power off?

3

Cooling fans will operate for approximate 2 minutes after projec-

Message disappears after 4 seconds.

tor is turned off. To power down completely, turn MAIN ON/OFF

 

SWITCH to OFF and disconnect AC Power Cord.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design CompatibilityPreparation Name of Each Part of ProjectorConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Lens InstallationPositioning Projector Preparation Picture Level and Tilt Adjustment Moving ProjectorReplacement of Terminal Connecting ProjectorTerminals of Projector Audio Input Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputBNC Input Jacks AV Input VIDEO/Y, C JacksSerial Port OUT Terminal Reset ButtonSerial Port Terminal JackConnecting to Computer Terminals ProjectorConnecting to Video Equipment TerminalsBefore Operation Side Controls and IndicatorsSide Controls Lamp Indicator IndicatorsReady Indicator Lamp Replace IndicatorOperation of Remote Control Laser Pointer FunctionZoom Button Volume ButtonWired Remote Jack Focus ButtonOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus Adjustment Adjusting ScreenZoom Adjustment Keystone AdjustmentBasic Operation Picture Freeze Function Timer FunctionNo Show Function Menu Operation Sound AdjustmentDirect Operation Sound MenuSelecting Computer System Computer InputSelecting Input Source InputAuto Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually PC System MenuComputer Input Compatible Computer Specifications ResolutionPC Adjust Menu PC AdjustmentAuto PC Adjustment Computer InputComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image AdjustmentImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuWhen Select Input 2 5 BNC Slot Video InputVideo Input Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Tint Video Input Image Level AdjustmentColor Progressive scanProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Remote Control Unit To change code of ProjectorLamp counter reset Wireless Mouse modeProjector mode USBInstallation Operating Wireless MouseMaintenance Operating Wireless MouseAppendix AIR Filter Care and Cleaning Cleaning Projection LensAppendix Lamp Management Yellow Lamp Dim Lamp Red Lamp Mark on LampAppendix Lamp Replacement Front Indicators Rear IndicatorsLamp Handling Precautions Troubleshooting Service Technical Specifications Appendix Configurations of Terminals DVI-I Terminal DIGITAL/ANALOGSerial Port IN/OUT Terminal Appendix Appendix Appendix Part No -A 610 318 4647 1AA6P1P4699-- MT8K
Top Page Image Contents