Acer 707 specifications Technical information, Self test pattern, Safety protection, Timing guide

Page 4

2.3 Self test pattern

The monitor may display a three colors test pattern. This is to indicate that the monitor is functioning properly, but the computer’s video signal is not reaching the monitor. In this case, please make sure the video cable is properly connected. The test pattern will disappear when the monitor is able to receive the video signal. However, if the test pattern does not display all three colors (blue, green and red), the monitor is not functioning properly. Please contact your local dealer for assistance.

2.4 Safety protection

The safety protection function is protecting for the monitor itself. When frequency of video signal from computer’s was out of range, (please refer to monitor “specifications”) The monitor will protect by itself and a warning message of OSD will appear on the screen, warning you to resetting monitor type on your computer.

2.5 Timing guide

This multi-scanning monitor can automatically detect and display several video modes. If the monitor recognizes one of preset timing signals, it will reset that mode and any stored display adjustments you have made.

The factory preset modes as indicated in the following table

Mode

Resolution

Fh.

Fv.

Mode

Resolution

Fh.

Fv.

(dots x lines)

(dots x lines)

 

 

 

 

 

 

1

720 × 400

31.47

70

7

800 × 600

63.90

100

 

 

 

 

 

 

 

 

2

640 × 480

31.47

60

8

1024 × 768

48.36

60

 

 

 

 

 

 

 

 

3

640 × 480

43.27

85

9

1024 × 768

60.02

75

 

 

 

 

 

 

 

 

4

800 × 600

46.87

75

10

1024 × 768

68.67

85

 

 

 

 

 

 

 

 

5

800 × 600

37.88

60

11

1600 × 1200

75.01

60

 

 

 

 

 

 

 

 

6

800 × 600

53.67

85

 

 

 

 

 

 

 

 

 

 

 

 

Fh: Horizontal Frequency (KHz)

Fv: Vertical Frequency (Hz)

Page 4

3.Technical information

3.1Products specifications

Picture tube (flat Screen CRT)

 

 

Size:

17-inch (43.18 cm) diagonal

Dot pitch:

0.25mm

Surface / transmission:

Tinted screen glass non-glare, black matrix

 

 

Maximum viewable area

16.02” (40.69cm) diagonal

 

 

Display size (factory setting)

310 mm (H) x 230 mm (V)

12.20 inch (H) x 9.06 inch (V) ( Adjustable)

 

 

 

 

Synchronization range

 

 

Horizontal frequency:

30-86KHz

Vertical frequency:

50-160Hz

Max. Resolution

1600x1200

 

 

Recommended resolution

1024x768 /85Hz

 

 

Dot Rate

150MHz

 

 

 

Power supply (universal)

 

 

Input Voltage:

AC 100-240V 60/50 Hz

Consumption:

110 watts maximum.

Input signal

Video: Analog 0.7Vp -p / 75 Ohms

Sync. : Separate sync. TTL level

 

Display Analog Input

Unlimited Number of colors

(depends upon video card)

 

Weight

 

 

Net :

18.5kg (40.7Lb)

Gross :

21.0kg (46.2Lb)

Unit dimension (W x H x D)

410 x 412 x 420 (mm)

 

 

 

Operating condition

 

 

Temperature:

5°C~40°C (41°F to 104°F)

Humidity:

20

~ 80

 

 

 

Storage condition

 

 

Temperature:

-20°~60°C (-4°F to 140°F)

Humidity:

10

~ 90

 

 

DDC1/DDC2B (Plug and Play)

VESA standard

 

 

 

NOTE: All technical specifications are subject to change without notice.

Page 5

Image 4
Contents Table of Contents Installation Precautions when using this monitorHow to install/remove the swivel base Fig PackageFront control locations and functions Adjust and ProgrammingOperation Safety protection Products specificationsTechnical information Self test patternSignal connector pin assignment TroubleshootingFederal Communications COMMISSIONF.C.CSTATEMENT