How to set the value, 001 | Mitsubishi Electronics HC5000 manual

ITEM	ASCII	HEX				VALUE

CLAMP POSITION	CLP	43h	4Ch	50h		001 - 255
CLAMP WIDTH	CLW	43h	4Ch	57h		01 - 63
VERT.SYNC.	VSC	56h	53h	43h		0	(OFF), 1 (AUTO)
LPF	LPF	4Ch	50h	46h		0	(OFF), 1 (ON)
SHUTTER(U)	SHU	53h	48h	55h		00 - 32
SHUTTER(L)	SHL	53h	48h	4Ch		00 - 32
SHUTTER(LS)	SHLS	53h	48h	4Ch	53h	00 - 95
SHUTTER(RS)	SHRS	53h	48h	52h	53h	00 - 95

*1) Setting range differs depending on the input signals.

•Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

How to set the value

Use the ASCII or HEX code as shown below to set the value.

ASCII

'+'

'–'

'0'

'1'

'2'

'3'

'4'

'5'

'6'

'7'

'8'

'9'

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands	Status code from	Description
from the PC, etc.	the projector
30 30 41 50 4F 4E 31 0D		Command for setting the
'0' '0' 'A' 'P' 'O' 'N' '1' ' '		AUTO POWER ON to ON

	30 30 41 50 4F 4E 31 0D	Command receipt confirmation
	'0' '0' 'A' 'P' 'O' 'N' '1' ' '	(Command echo back)

[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the CONTRAST B to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands		Status code from	Description
from the PC, etc.		the projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D			Command for setting the
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '	'		picture control

		30 30 50 2B 31 30 2B 30 30 2D 30 35 0D	Command receipt confirmation
		'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '	(Command echo back)

[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands	Status code from	Description
from the PC, etc.	the projector
30 30 53 0D		Command for checking
'0' '0' 'S' ' '		the TINT setting

	30 30 53 2B 31 30 0D	Check result (+10)
	'0' '0' 'S' '+' '1' '0' ' '

• To set TINT at 0, enter +00. (-00 is invalid.)

[Example 4] When setting the REFERENCE of GAMMA MODE-USER1 to CINEMA (+2), ADJUST MODE to RED (R), HIGH to -2, MID to +3 and LOW to 0. (Figures and symbols enclosed in quotation marks are ASCII codes.):

*There is no command for selecting ALL for ADJUST MODE. Even when you want to set all the three colors to the same value, send a command for each of R, G, and B respectively.

Sending commands		Status code from	Description
from the PC, etc.		the projector
30 30 47 53 55 31 52 2B 32 2D 30 32 2B 30 33 2B 30 30 OD			Command for setting GAMMA
'0' '0' 'G' 'S' 'U' '1' 'R' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' '	'		MODE-USER1

		30 30 47 53 55 31 52 2B 32 2D 30 32 2B 30 33 2B 30 30 OD	Command receipt confirmation
		'0' '0' 'G' 'S' 'U' '1' 'R' '+' '2' '-' '0' '2' '+' '0' '3' '+' '0' '0' ' '	(Command echo back)

001 - 255

How to set the value

MODE-USER1