ITEM | ASCII | HEX |
|
|
| VALUE |
CLAMP POSITION | CLP | 43h | 4Ch | 50h |
| 00 - 63 |
CLAMP WIDTH | CLW | 43h | 4Ch | 57h |
| 01 - 63 |
VERT. SYNC. | VSC | 56h | 53h | 43h |
| 0 (AUTO), 1 (OFF) |
SHUTTER (U) | SHU | 53h | 48h | 55h |
| 00 - 20 |
SHUTTER (L) | SHL | 53h | 48h | 4Ch |
| 00 - 20 |
SHUTTER (LS) | SHLS | 53h | 48h | 4Ch | 53h | 00 - 20 |
SHUTTER (RS) | SHRS | 53h | 48h | 52h | 53h | 00 - 20 |
*1) When sRGB is ON, only the main data are effective.
•Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII | '+' | '0' | '1' | '2' | '3' | '4' | '5' | '6' | '7' | '8' | '9' | |
HEX | 2Bh | 2Dh | 30h | 31h | 32h | 33h | 34h | 35h | 36h | 37h | 38h | 39h |
[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands | Status code from | Description |
from the PC, etc. | the projector |
|
30 30 41 50 4F 4E 31 0D |
| Command for setting the |
'0' '0' 'A' 'P' 'O' 'N' '1' ' ' |
| AUTO POWER ON to ON |
|
|
|
| 30 30 41 50 4F 4E 31 0D | Command receipt confirmation |
| '0' '0' 'A' 'P' 'O' 'N' '1' ' ' | (Command echo back) |
|
|
|
The data code of CONTRAST and BRIGHTNESS consists of the difference data between R and G, the main data, and the difference data between B and G.
[Example 2] When setting the difference data between R and G to +10, the main data to 0, and the difference data between B and G to
Sending commands |
| Status code from | Description |
from the PC, etc. |
| the projector |
|
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D |
| Command for setting the | |
'0' '0' 'P' '+' '1' '0' '+' '0' '0' | ' |
| picture control |
|
|
|
|
|
| 30 30 50 2B 31 30 2B 30 30 2D 30 35 0D | Command receipt confirmation |
|
| '0' '0' 'P' '+' '1' '0' '+' '0' '0' | (Command echo back) |
|
|
|
|
[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in quotation marks are ASCII codes.)::
Sending commands | Status code from | Description |
from the PC, etc. | the projector |
|
30 30 53 0D |
| Command for checking |
'0' '0' 'S' ' ' |
| the TINT setting |
|
|
|
| 30 30 53 2B 31 30 0D | Check result (+10) |
| '0' '0' 'S' '+' '1' '0' ' ' |
|
|
|
|
•To set 0 in the menu setting commands (COLOR MATRIX, COLOR, TINT, SHARPNESS), enter +00.
5