To operate projector power ON
|
|
|
|
|
|
| USB |
|
|
|
|
|
| ||
REMOTE REMOTE | INPUT 1 | R/PR | G/Y | B/PB | H/HV | V | |
IN | OUT | ||||||
MAIN |
| INPUT 2 |
| AUDIO |
|
| VIDEO |
2, 13 |
|
|
| IN |
| 2 | |
|
|
| AUDIO | Y |
| 1 | |
|
|
|
|
|
|
| VIDEO |
|
|
|
| OUT |
|
|
|
| AC IN |
|
|
| C |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| L |
|
|
|
|
|
|
| AUDIO |
|
|
|
|
|
|
| R |
ENGLISH
AUTO POSITION button
6, 8 4
TEMP LAMP POWER
AUTO POSITION LENS SHIFT
ENTER
MENU
KEYSTONE 
ZOOM/
FOCUS
VOLUME
SOURCE MUTE
3, 11, 12 9
105, 7 6, 8
5, 7
MUTE button 9
COMPUTER 
1 2
KEYSTONE | VIDEO |
1 2
ZOOM/FOCUS EXPAND AUTOPOSITION
VOLUME |
|
| LASER |
MENU | ENTER | |
P in P | STILL | 16 : 9 |
| MUTE |
|
LENS SHIFT
3, 11, 12
4
AUTO POSITION button
10
MUTE button
1.Turn on the equipment connected to the projector.
2.Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
3.Turn the projector on by pressing the POWER but- ton. The light source lamp starts warming up, even- tually turning completely on.
•The lamp may take about a minute to light up.
•The lamp occasionally fails to light up. Try to light up the lamp again after a few minutes.
•If the projector has not cooled down completely since the last
indicator | LAMP | POWER | |
condition | |||
|
| ||
- | red | ||
when light source lamp is on | green | green | |
light source lamp held off temporarily | - | red |
Important:
•A darkened image may be seen right after pressing the POWER button due to warming up of this pro- jector. While warming up, no other commands can be accepted.
•After the power is turned on or the LAMP MODE is changed, the screen may flicker before the lamp op- eration becomes stable. This is due to the charac- teristics of the lamp, not a failure of the lamp.
•When the lamp indicator is blinking red, the ser- vice life of the lamp is about to end. Replace the lamp. See pages 22 and 26.
•The picture might not be of optimum performance in extreme hot or cold conditions. (The projector is not malfunctioning.)
4.Press the ZOOM/FOCUS button to FOCUS. “FO- CUS” will appear on the display.
5.Adjust with the + or - button to get a fine picture.
6.Select the desired external input source by using the COMPUTER 1,2 or VIDEO1,2 button on the re- mote control or the SOURCE button on the control panel.
•Pressing the SOURCE button on the control panel repeatedly will select VIDEO 1, VIDEO 2, COM- PUTER 1 and COMPUTER 2.
•The projector automatically selects the appropriate signal format. The selected signal format is dis- played on the screen.
•The COMPUTER, VIDEO or SOURCE buttons do not work when MENU is displayed. At this time, the prohibition mark ( ) appears on the screen.
•When selecting the COMPUTER input, the image may flicker. Press the $ or % button to adjust the image.
•The intensity of the lamp will be STANDARD for 2 minutes regardless of the setting of the LAMP MODE when the lamp turns on.
7.Press the ZOOM/FOCUS button to ZOOM. “ZOOM” will appear on the display.
8.Adjust with the + or - button to get an approximate size.
9.Press the LENS SHIFT button. “LENS SHIFT” will appear on the display.
10.Adjust with the {, }, $ or % button to get an approximate lens position.
•If necessary, adjust focus, zoom and lens shift again.
•Focus, zoom and lens shift adjustment is possible in the normal picture mode only. In PinP or EXPAND mode, the adjustment is prohibited.
EN – 13