Mitsubishi Electronics XL5U user manual Menu operation

Menu operation (continued)

1IMAGE

CONTRAST ......... Use to adjust the image contrast. The contrast becomes higher
			opt.	XGA60
as the value increases.
BRIGHTNESS ..... Use to adjust the image brightness. The image becomes
	IMAGE
brighter as the value increases.		CONTRAST		0
sRGB .................... Choose ON for projection emphasizing on the color
		BRIGHTNESS		0
reproducibility.
• When sRGB is ON, COLOR MATRIX, COLOR TEMP.,		sRGB		OFF
COLOR, TINT, and GAMMA MODE can't be adjusted.		COLOR MATRIX		COMPUTER
COLOR MATRIX . Use to adjust the color balance in each color of the image. See		COLOR TEMP.		STANDARD
page 18.		COLOR		0
COLOR TEMP. .... Use to adjust the color temperature. See page 18.		TINT		0
COLOR ................ Use to adjust the color intensity of the image.
		SHARPNESS		0
TINT .................... Use to adjust the color balance of the image. The color balance
shifts to green as the value increases and shifts to purple as		GAMMA MODE		AUTO
the value decreases. (Available only when VIDEO is chosen as
the source.)

• When the TV50 (PAL, SECAM) signal is input, TINT can't be adjusted.

SHARPNESS ....... Use to adjust the image sharpness. The image becomes sharp as the value increases. (Available only

when VIDEO is chosen as the source.)

GAMMA MODE ... When AUTO is selected, the appropriate gamma mode is automatically selected depending on the input signal. For normal use, select AUTO. Select DYNAMIC for computer sources. Select STANDARD for sport scenes and video sources. Select THEATER for film sources.

2 INSTALLATION				opt.	XGA60
AUTO POWER ON ...... When ON is chosen, the lamp is automatically lit when the
power cord is plugged in the wall outlet. Choose ON when	INSTALLATION
using the projector mounted on the ceiling.			AUTO POWER		OFF
			ON
• The projector is in the stand-by mode when the lamp			AUTO POWER		OFF
is off. Use the remote control to turn on the lamp.			OFF
			IMAGE		SETUP
AUTO POWER OFF Use to set the time elapsed before the projector enters the			CAPTURE
			SPLASH		ON
		ON
stand-by mode when there is no signal input from the source.			SCREEN
IMAGE CAPTUREUse to capture the screen for the splash screen. See page 21.			BACK COLOR		BLUE
SPLASH SCREEN Choose ON to display the splash screen when the power is			MUTE MODE		BLACK
turned on.			LAMP MODE		STANDARD
• The splash screen can be changed. See page 21.			IMAGE		OFF
BACK COLOR ...... Use to select the background from among BLUE, BLACK and			REVERSE

IMAGE, which will be displayed when there is no signal input from the source. When IMAGE is selected, the splash screen will be displayed.

MUTE MODE ...... Use to choose the background, either BLACK, or IMAGE, which will be displayed when the MUTE

button is pressed. When IMAGE is chosen, the splash screen will be displayed.

LAMP MODE ....... Use to change the brightness of the lamp. When LOW is chosen, the lamp brightness is kept low

and the volume of the operation sound is reduced, resulting in a longer lamp replacement interval.

•The STANDARD LAMP MODE is activated by default whenever the projector is turned on. When the LOW LAMP MODE has been chosen, the default STANDARD LAMP MODE is switched to the LOW lamp mode in 1.5 minutes.

•When the LAMP MODE is switched, the projected image may flicker. This is not a

product malfunction.

For XL5U only

•You can fix the LAMP MODE to LOW.

How to fix the LAMP MODE to LOW

In stand-by mode, keep pressing the AUTO, KEYSTONE, and COMPUTER buttons on the control panel together about three seconds. (The STATUS indicator is lit in orange for one second.)

How to cancel the fixed LAMP MODE

In stand-by mode, keep pressing the VIDEO, KEYSTONE, and } buttons on the control panel together about three seconds. (The STATUS indicator is lit in green for one second.)

Important:

• Within 10 seconds after the STATUS lamp is lit, do not unplig the power cord nor turn the POWER button to ON.

IMAGE REVERSE .. Use to reverse the projected image. Select MIRROR for rear projection with the tabletop-mounted projector. Select MIRROR INVERT for front projection with the ceiling-mounted projector.

•When you continue projection for a long time with BACK COLOR or MUTE MODE set to IMAGE, an after- image may persist on the screen.

•Do not change the setting of LAMP MODE frequently.

•You can’t set IMAGE CAPTURE or SPLASH SCREEN when PASSWORD FUNCTION in the FEATURE menu has been set to SPLASH ID SCREEN to enable the password lock.

EN – 16