Mitsubishi Electronics XD510U-G Image adjustment, BrilliantColorTM, LPF Progressive filter

Page 22

Image adjustment (continued)

BrilliantColorTM

Use this setting to make colors with medium brightness, such as yel- low and the skin tone appear natural. Press the W button to decrease the value to lessen the effect. Press the X button to increase the value to heighten the effect. (BrilliantColorTM has no effect at value 0.)

6.Select a value by pressing the W or X button.

For more enhanced color reproduction, set BrilliantColorTM to 0. The white area of the color wheel is disabled, and you can reproduce true-color images.

RGB-COLOR

Use to adjust the color intensity of the projected image. Every time the

Xbutton is pressed, the color becomes thicker. Every time the W but- ton is pressed, the color becomes lighter.

RGB-TINT

Use to adjust the color balance of the projected image. Every time the

Xbutton is pressed, the image appears more greenish. Every time the W button is pressed, the image appears more reddish.

This projector automatically and properly projects video signals being input from the computer. However, some video signals may not be projected, depending on the type of the computer. When it occurs, press the AUTO POSITION button. (See page 14.) When the signal is still not projected properly, adjust the projected image using the SIG- NAL menu.

How to adjust the image supplied from the computer using the menu:

Perform the following procedures when the following conditions occur. When wide strips appear

................. adjust TRACKING in the SIGNAL menu.

When the projected image flickers When the projected image is blurred

................. adjust FINE SYNC. in the SIGNAL menu.

When the projected image is displaced horizontally

................. adjust HORIZ.POSITION in the SIGNAL

menu. Every time the W button is pressed, the image moves to the right. Every time the

Xbutton is pressed, the image moves to the left.

When the projected image is displaced vertically

................. adjust VERT.POSITION in the SIGNAL

menu. Every time the W button is pressed, the image moves down.

Every time the X button is pressed, the image moves up.

When the top part of the image flags

................. change the setting of HOLD in the SIGNAL

menu. To select ON , press the ENTER button, and adjust BEGIN or END to mini- mize the flagging.

A solid black or solid white appears in the image

................. adjust CLAMP POSITION or CLAMP

WIDTH in the SIGNAL - USER menu. When the motion is not smooth.

................. adjust VERT. SYNC in the SIGNAL - USER

menu.

Select AUTO for most cases.

Noise appears in the right or left half of the image.

................. adjust SHUTTER(LS) or SHUTTER(RS) in

the SIGNAL - USER menu.

Noise appears in the top or bottom part of the image.

................. adjust SHUTTER(U) or SHUTTER(L) in the

SIGNAL - USER menu.

1.Display the SIGNAL menu.

2.Press the S or T button to select a setting to adjust.

3.Adjust the selected setting by pressing the W or X button.

To cancel the menu:

4.Press the MENU button.

Do not change the settings of the SIGNAL menu for ordinary use.

Simple method to adjust the image position

To adjust the horizontal position:

1.Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the right edge of the image with the right side of the screen by adjust- ing TRACKING.

2.Repeat step 1 to complete the adjustment of the horizontal position.

To adjust the vertical position:

3.Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION.

LPF (Progressive filter)

You can select to enable or disable the LPF. This option is set to OFF normally.

Vertical or horizontal streaks may appear in the projected image, depending on the type of the DVD player, game console or computer in use. If this occurs, reduce noise by enabling the LPF. Projected images appear slightly faint.

EN-22

Image 22
Contents XD510U XD510U-G SD510U When using the projector in Europe only for XD510U/ SD510U ShockContents Important safeguards Do not unplug the power cord during operation Do not keep using the damaged projectorDo not look into the lens when the projector is operating Place of installationControl panel Terminal board OverviewKensington Lock Overview Remote controlBottom side Operation range of the remote control Remote controlBattery installation Reception angle vertical Reception angle horizontalFront projection InstallationLayout of the projector Front projection, ceiling mountingProjector + AV device Basic connectionsProjector + DVD player or Hdtv decoder Basic connections Projector + ComputerUsing the adjustment feet rear Adjustment of the projection angleUsing the adjustment feet front PreparationStatus Power Power-onWhen fine streaks are seen on projected images Basic operationBasic operation When connecting to a laptop computer Wall ScreenAuto Menu operationContrast Theater UserMenu Options Menu operationBasic operation Image menuInstallation menu Feature menu Singal menu Signal User menuInformation menu Gamma mode Image adjustmentAdjusting projected images Color EnhancerBrilliantColorTM Image adjustmentSimple method to adjust the image position LPF Progressive filterAdvanced features FreezeTo use the Magnify mode Advanced featuresTo cancel the password function MagnifyLamp replacement When the projector is mounted to the ceilingInterval of lamp replacement Lamp replacementReset of the lamp operation time Power Status TroubleshootingNo image appears on the screen Images are not displayed correctly TroubleshootingLPF Cleaning of the lens MaintenanceCleaning of the projector and the ventilation slots OthersNormal condition IndicatorsAbnormal condition Specifications Dimensional drawings unit mm SpecificationsConnectors What’s included in the boxVGA60 CGA84CGA85 VGA72Mitsubishi Electric Corporation
Related manuals
Manual 6 pages 43.84 Kb