Mitsubishi Electronics FL6900U Viewing computer images, Plugging the power cord, About DDC

Page 14

Viewing computer images (continued)

Monitor

1 MONITOR OUT

RGB cable

To audio input terminals

2

1 AUDIO OUT

Audio cable (option)

For monitor connection:

1.Connect the RGB cable from the monitor to the MONITOR OUT terminal of the projector.

For audio output connection:

1.Connect one end of a commercially available audio cable to the AUDIO OUT terminal of the projector.

2.Connect the other end (white and red) of the audio cable to the audio input terminals (L, R) of the audio equipment.

•When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.

About DDC

The COMPUTER/COMPONENT VIDEO IN 2 terminal of this projector complies with the DDC1/2B standard and the COMPUTER/COMPONENT VIDEO DVI-D(HDCP) terminal complies with the DDC2B standard. When a computer supporting this standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate images.

•When connecting a DDC-supporting computer to the projector, turn on the main power switch of the projector before starting the computer.

B. Plugging the power cord

•In order to ensure the safety in case of trouble with the projector, use an electrical outlet having an earth leakage breaker to supply the power to the projector. If you do not have such outlet, ask your dealer to install it.

1. Plug the attached power cord into the power cord inlet of this projector.

2. Plug the other end of the power cord into a power outlet.

Earthing terminal

1

2

 

 

Power cord (example)

•The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.

•This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.

•The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power cord separately.

•Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.

•Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.

•Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.

Caution:

•Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.

•Do not plug in or out the power cord with your hand wet. It may cause electric shock.

EN-14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents FL6900 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards Important safeguards Do not keep using the damaged projectorRemoving the batteries from the remote control Checking accessoriesInserting the batteries into the remote control Preparing your projectorControl area Terminal board Preparating your projectorOverview Remote control Bottom sideUsing the wired remote control Using the remote controlOperational range of the remote control Reception angleWhen the aspect ratio of the screen is Setting up your projectorSetting up the screen Screen size and projection distanceWhen fine streaks are seen on projected images Setting up your projectorAdjusting the position of the projected image When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesAbout DDC Plugging the power cordViewing computer images For monitor connectionProjecting images Remove the lens capTo stop projecting When connecting to a notebook computerSetting of the resolution AV muteViewing video images Connecting the projector to video equipmentConnecting to a video player, etc Connection for video equipment having an Hdmi terminal Viewing video imagesProjector + DVD player or Hdtv decoder Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-20 How to change the settings With the remote control Volume from the speakerSetting the aspect ratio With the Feature menuSetup Menu operationMenu operation How to set the menusAvailable settings in the menus Auto Power OFF Lamp ModeAuto Power on On / OFF Mute Mode Black / ImageVideo Signal Password FunctionCinema Mode Auto Setup AutoEN-26 Lamp Time LOW ResolutionDescription InputTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerHow to adjust the computer image YESTo adjust the vertical position Simple method to adjust the image positionTo adjust the horizontal position LPF Progressive filterSet the background color Advanced featuresSetting procedure Set the image sizeTo cancel the password function Advanced featuresPassword function To enable the password functionFreeze To use the split modeSplit To change the input source of the left or right screenOperation Mouse remote controlProjector + computer with USB connector USBPJLink Supervising and controlling by computerProjectorView About PJLinkAbnormal condition IndicatorsNormal condition ConditionProcedure for changing batteries Terminal cover with anti-theft alarm deviceProcedure for setting the anti-theft alarm device Interval of lamp replacement Replacing the lampTo replace the lamp Reset of the lamp operation timeReplacing the lamp Cleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensTroubleshooting No image appears on the screen Problem SolutionTroubleshooting Images are not displayed correctly Problem SolutionOthers Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsSpecifications XGA85Real mode ConnectorsDimension drawings unit mm Without terminal cover With terminal coverMitsubishi Electric Corporation
Related manuals
Manual 48 pages 8.76 Kb Manual 2 pages 6.49 Kb
Top Page Image Contents