Mitsubishi Electronics user manual Replacing the lamp, Spare lamp for EX200U/ES200U VLT-EX240LP

Page 41

Replacing the lamp

 

Spare lamp for EX200U/ES200U: VLT-EX240LP

• Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp.

•To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

•To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

•To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces. To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

•Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation may also result in fire.

•If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The glass fragments may fall out and cause injury to your eyes.

•In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.

•Contact your dealer when replacing the lamp unit with the projector mounted to the ceiling.

•Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a breakdown.

•This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the lamp may explode soon after the start of use.

•The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.

•When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor immediately.

•This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

•Be sure to use the lamp dedicated to this projector, VLT-EX240LP for EX200U and ES200U. Use of other lamps may cause a failure of the projector.

ENGLISH

1.Turn the power off and disconnect the projector from the wall socket. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2.Unscrew the screws on the lamp cover.

3.Remove the lamp cover from the projector.

1 , 2

Pull up the lamp cover, pussing up the allow parts of the front panel.

• Do not turn the power on with the lamp cover removed.

•Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

4.Remove and dispose of the lamp protection film. 3

2

 

2

 

 

 

1

3

 

 

5.Loosen the screw that secures the lamp.

1

2

EN-41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents EX200U/ES200U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewProjector Controls and functionsMagnifying and searching for details on page 24 for Remote controlRemote control effective range Obtaining a preferred projected image size Positioning your projectorChoosing a location When fine streaks are seen on projected images Front projection Layout of the projectorConnecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerTo connect the projector to a monitor Connecting Video source devicesConnecting a monitor To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Setting a password Utilizing the password functionIf you forget the password Entering the password recall procedureDisabling the password function Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modeSetting the User 1/User 2 mode Optimizing the imageFine-tuning the image quality in user modes 3D Color Management Using Wall ScreenHow to use the Timer On key? Setting the presentation timerTo cancel the timer, perform the following steps Hiding the image Adjusting the soundLocking control keys Freezing the imageShutting down the projector Direct power offPersonalizing the projector menu display Menu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color System Setup Basic menu System Setup Advanced menu Security Settings Advanced menu Care of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as LowLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampSpare lamp for EX200U/ES200U VLT-EX240LP Replacing the lampResetting the lamp timer EN-43 Light Status & Description Power Temp Lamp Power events IndicatorsTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Component-YPbPrinput Mitsubishi Electric Corporation
Related manuals
Manual 50 pages 15.1 Kb

ES200U, EX200U specifications

The Mitsubishi Electronics EX200U and ES200U are innovative and highly efficient solutions designed to meet the demands of modern automation and control systems. Tailored for both industrial and commercial applications, these servo drives enhance performance while ensuring reliability and precision.

At the core of the EX200U and ES200U models is advanced motion control technology. These servo drives leverage high-resolution feedback systems to deliver exceptional positioning accuracy, which is critical in applications such as robotics, CNC machinery, and advanced manufacturing processes. The integration of Mitsubishi’s proprietary algorithms allows for real-time processing of motion commands, enabling smoother operations and reducing mechanical stress.

One of the standout features of the EX200U and ES200U is their versatility. These servo drives support a wide range of motor types, including synchronous and asynchronous motors, making them suitable for various operational demands. With scalable performance, users can easily adjust settings to match the specific needs of their applications, whether they require high speed or high torque.

Energy efficiency is another essential characteristic of the EX200U and ES200U. Both models are designed to minimize energy consumption without sacrificing performance. The incorporation of regenerative braking technology allows for energy to be recaptured during deceleration, contributing to lower operational costs and a smaller environmental footprint.

The user-friendly interface of the EX200U and ES200U simplifies configuration and monitoring. With intuitive software tools, engineers can quickly set up, program, and fine-tune the drives. The ability to interface seamlessly with Mitsubishi’s broader automation ecosystem enhances operational cohesion, allowing for standardized control and data analytics across multiple devices.

Safety is also prioritized in the design of the EX200U and ES200U. These servo drives come equipped with integrated safety features, including safe torque off and error handling capabilities that protect both equipment and personnel. Compliance with international safety standards further reinforces their reliability in industrial environments.

In summary, the Mitsubishi Electronics EX200U and ES200U servo drives represent a blend of advanced technology, user-centric design, and energy efficiency. With their impressive features and capabilities, they are well-equipped to handle the demands of contemporary automation, providing users with reliable and precise control for a wide array of applications.
Top Page Image Contents