When an Indicator is Lit or Flashing
The indicators on the projector’s control panel light or flash to | POWER | STANDBY | STATUS | ||
notify of problems, as described below. | indicator | indicator | indicator | ||
An indicator is also used to notify you of the currently set power |
|
|
|
|
|
mode. See “Power Cable Connections and Switching the Power |
|
|
| STATUS |
|
On/Off” on page |
|
| STANDBY | MENU | |
|
|
|
| ||
|
| POWER |
|
| |
|
|
|
|
| |
|
|
|
| MENU |
|
|
|
| K |
| |
|
|
| IC |
|
|
|
|
|
| E |
|
|
|
| N |
|
|
|
| O |
|
|
| T | |
|
| S |
| |
| Y |
|
| |
K | E |
|
|
|
|
|
|
| |
E
CRUOS
| A | U |
|
| T |
|
| T |
|
| S |
| Y | |
E |
| |
K |
|
|
|
|
|
| Indicator status | What you should do | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| When the power is on (Lit green) | It is time to replace the lamp. | |
| POWER |
|
|
|
| |||
|
|
|
|
| ||||
| STANDBY | STATUS | Replace with a new lamp cartridge. | |||||
|
|
|
|
|
|
| Lit red | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Standby mode (Lit green) |
|
|
|
|
|
|
|
|
|
|
| POWER |
|
|
|
|
| The lamp has reached the end of its service life. The power | |
| STANDBY | STATUS | will no longer turn on. | |||||
|
|
|
|
|
|
| Lit red | |
|
|
|
|
|
|
| The projector can be used for 100 hours after the lamp has reached | |
|
|
|
|
|
|
| Blinks green for 60 seconds (then, | |
|
|
|
|
|
|
| the end of its service life. | |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| lit green) | Replace with a new lamp cartridge. |
|
|
|
|
|
|
|
|
|
| POWER | STATUS Blinks red | The lamp cover is open. | |||||
| STANDBY | The lamp cover is not properly mounted. Mount it properly. | ||||||
|
|
|
|
|
|
| (1 second on/1 second off) | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Lit green |
|
The temperature is abnormally high.
•The temperature protector has been activated. If the room tem-
|
| POWER |
|
|
| Blinks red | perature is high, move the projector to a cool place. If the | |
|
| STANDBY | STATUS |
| projector’s internal temperature is high, check the cooling fan’s | |||
|
|
|
|
|
|
| (0.5 seconds on/0.5 seconds off) | |
|
|
|
|
|
|
| ventilation slots and clean them if they are clogged. | |
|
|
|
|
|
|
| Lit green | |
|
|
|
|
|
|
| • When the temperature protector is activated, the power turns | |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| off and in some cases will not turn back on immediately. In this |
|
|
|
|
|
|
|
| case wait about 90 seconds, then try again. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Lit green | The fan has stopped. | |
|
| POWER |
|
|
| |||
|
| STANDBY | STATUS |
| Blinks red | Unplug the power cable and contact a store that sells the KG- | ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| (0.5 seconds on/0.5 seconds off) | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Lit green |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| POWER |
|
|
| Blinks red quickly | The lamp will not light. | |
|
| STANDBY | STATUS |
| Wait at least 90 seconds, then turn the power back on. If the prob- | |||
|
|
|
|
|
|
| (0.1 seconds on/0.1 seconds off) | |
|
|
|
|
|
|
| lem persists, unplug the power cable and contact a store that sells | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Lit green | the |
Should an indicator be in a condition other than normal or flash at a rate other than the aforementioned, disconnect the power cable and contact your store of purchase.
Thermal Protector
If the temperature within the projector becomes abnormally high, the thermal protector will be activated and will switch off the power of the projector.
Should this happen, please take the following actions.
1.Switch off the power and disconnect the power plug from the wall outlet.
2.Check the following matters and take the required measures.
When the projector is being used in a location that has a high ambient temperature, set it up again in a cool location. Check the outflow and intake holes and clean them if they are obstructed.
3.Wait about 60 minutes until the temperature of the projector drops.
If after having performed the above matters, the problem still has not been solved, please contact your store of purchase.