Pioneer DEH-P5900IB installation manual DIN Rear-mount, DIN Front/Rear-mount, DIN Front-mount

Installation

Note:

1. Insert the mounting sleeve into the dashboard.

ENGLISH

DIN Rear-mount Fastening the front panel

Connecting the Units

Note:

ENGLISH

• Control signal is output through blue/white cable

• Check all connections and systems before final

installation.

• Do not use unauthorized parts. The use of

unauthorized parts may cause malfunctions.

• Consult with your dealer if installation requires

drilling of holes or other modifications of the

vehicle.

• Do not install this unit where:

— it may interfere with operation of the vehicle.

	• When installing in a shallow space, use a sup-
	plied mounting sleeve. If there is enough
	space behind the unit, use factory supplied
	mounting sleeve.
2.	Secure the mounting sleeve by using a screwdriv-
	er to bend the metal tabs (90°) into place.
3.	Install the unit as illustrated.

Removing the Unit

1.Extend top and bottom of the trim ring outwards to remove the trim ring. When reattaching the trim ring, push the trim ring onto the unit until it clicks. (If the trim ring is attached upside down, the trim ring will not fit properly.)

•It becomes easy to remove the trim ring if the front panel is released.

If you do not plan to detach the front panel, the front panel can be fastened with supplied screws and holders.

1. Attach the holders to both sides of the front panel.

•When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result.

		CC
	F	A	O		F	O
			N			N
O	F			O	F

when this unit is powered on. Connect it to an

external power amp’s system remote control or

the vehicle’s auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is

equipped with a glass antenna, connect it to the

antenna booster power supply terminal.

• Never connect blue/white cable to external power

amp’s power terminal. Also, never connect it to

the power terminal of the auto antenna.

— it may cause injury to a passenger as a result

of a sudden stop.

• The semiconductor laser will be damaged if it

1. Extend top and bottom of the trim ring outwards

to remove the trim ring. When reattaching the

trim ring, push the trim ring onto the unit until it

clicks. (If the trim ring is attached upside down,

Trim ring

Holder

		S			S
		T			T
	R	A		R	A
T			T

Otherwise, battery drain or malfunction may

result.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

MANUAL

DEH-P5900IB

MANUEL

overheats. Install this unit away from hot places

such as near the heater outlet.

• Optimum performance is obtained when the unit

is installed at an angle of less than 60°.

60°

the trim ring will not fit properly.)

• It becomes easy to remove the trim ring if the

front panel is released.

Trim ring

2.Determine the appropriate position where the holes on the bracket and the side of the unit match.

2. Replace the front panel to the unit.

ACC position No ACC position

• Use this unit in other than the following condi-

tions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the battery

• Black cable is ground. This cable and other prod-

uct’s ground cable (especially, high-current prod-

ucts such as power amp) must be wired separate-

ly. Otherwise, fire or malfunction may result if

they are accidentally detached.

• Cord function may differ according to the

product, even if cord color is the same. When

connecting this system, be sure to check all

manuals and connect cords correctly.

INSTALLATION

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

Printed in Thailand

Imprimé en Thaïlande

<XRD7143-A/N> UC <KMMZX> <06J00000>

D’INSTALLATION

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). For details, refer to the following installation methods.

DIN Front-mount

Installation with the rubber bush

Mounting sleeve

Dashboard

182

53Rubber bush

Screw

2.Insert the supplied extraction keys into both sides of the unit until they click into place.

3.Pull the unit out of the dashboard.

3.Tighten two screws on each side.

•Use either truss screws (5 mm ⋅ 8 mm) or flush surface screws (5 mm ⋅ 9 mm), depend- ing on the shape of screw holes in the bracket.

Screw

Dashboard or Console

Factory radio mounting bracket

3. Flip the holders into upright positions.

4.Fix the front panel to the unit using screws.

Screw

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive

tape around them where they lie against metal

parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s nega-

tive cables.